MAH14PRAWW Maytag Washer - Instructions

The first step to repairing this problem is to remove the hoses and back panel of the washer. Next detach both the hoses attached to the pump ( have some towels handy because their will be a lot of water pouring out of the pump). Before removing any screws on the pump, use a wrench to remove the bottom platform securing the pump inside of the washer. On the the Amana washer there should be about three bolts holding this small platform down. After unscrewing the bolts, unsnap the wire connected to the motor and remove the platform to get the entire pump out of the washer. The next step is to unscrew the screws on the bottom of the platform to release the base of the pump. The next step is to put the new pump on that same platform. FYI the new pump may not fit on the platform. To solve this problem, unscrew the motor/pump(the black thing) from the base holding the motor( the cream or white colored part). Do this step for the old and new motor/pump. Screw your new motor to the old base. Screw the base with the motor attached back on the platform. Connect the wire in the washer back to the motor. Screw the platform back in the washer and reconnect everything that was disconnected to remove the motor/pump. Finally put the back panel back on the washer and run a test cycle. The washer should now be able to drain.

removed one panel and front door to access under tub.leak solved!!!! thanks

Tilt washer onto door with back of washer on top for easier access.

Wow! Thanks to the customer info/hints already posted the repair went super smooth and was relatively easy to accomplish. $70.00 for an easily replaced part sure beats $1,000+ for a new washer. Super fast shipping reduced down-time significantly!!! From start to finish the job took less than 30 minutes. Thank you so much.

Off with the door. Off with the front panel. Lift the top and you are looking at the boot. Remove the boot retaining wire . Remove the boot and reverse the procedure. It's a snap.

Basic disassembly as described earlier.Some tips I found helpfull. Use vice grip pliers on spring.it will keep a grip on the spring hook and you can exert more force to pull the spring.Th bellows was very sticky and hard to slip into place. I put a litle silicone lube ( stuff you use for pool pump gaskets )on the bellows. It made it slip into place easly.

Download machine service manual from internet. This makes dismantling easy and prevents damage to component parts.

Dismantle as per manual and remove old bellow - easy.

Re-install new bellow on tub rim - EXTREMELY difficult. The spring that tensions the wire that holds the bellow in place is extremely powerful and in attempting to stretch it it often slips off the tub rim taking the bellow with it so you have to start all over again. It took me 2 hours to realise I would never be able to do this alone. With the help of a second pair of hands this was accomplished in 20 mins with some difficulty.
The rest of the installation and re-assembly was done without difficulty.

Despite the reviews by people who installed this part themselves, I knew that any type of repair was beyond my ability. I enlisted the assistance of a cousin who is a trained, professional appliance repairman. Despite not having instructions, with his experience things went well until he found he did not have the unique wrench that would have made life easier, but he was able to adapt and use the tools he had at hand. Unfortunatley, after more than twos hours attempting to install the wire around the boot, he realized that he could not do it alone, I had to help him and together, we were able to install the wire. It would have been helpful to have step by step instructions and a list of necessary (or at least useful) tools.

Removed the door and front panel with ease. Then came the spring and cable. People who say it was easy are not telling the whole story. Removing the spring was okay except for it flew across the room. Putting the new cable on with a pair of needlenose pliers did not work for me. I had to get a spring tool like you use on brakes on a car. Once I had the tool and secured the cable in place with a piece of wire I got the spring on. Everything except the spring took about 15 minutes.

1. ReMoved spring and cable from tub, 2. Remove bellow drain hose clamp at bottom of bellow, 3. Remove bellow from tub side and door frame, 4. Wet door frame with water and dish soap solution, 5. Press door frame side of bellow into slot. Align grooves, 6. slide tub side of bellow over tub edge, 7. Say a prayer to the good of your choice, 8. Reattach bellow cable with spring. This required use of double stands of 60lb braided fishing line to chinch most of the way and then use of a spring hook took in one hand and needle nose in the other. No less than 12 attempts. Be sure to have another pair of hands ready when doing and the whole job will take about 15 to 20 minutes.

Being a seventy five year old man I was reluctant to taking on this job but after getting prices for the repair or replacing the machine I cringed and trying to save some money I took on this job.Got all the information I could find on line I got started.Taking machine apart was easy and remembering to keep parts separated is something I learned from my mechanical back round is a must.Pictures also help.Taking out spinner drum easy.Bearings a nightmare If you don't have a bearing removal tool.Front bearing had to be cut out with a dremel tool and zip wheel being careful not to destroy the race.Removed spindel from spinner drum as I could see that for me to put shaft in hole would have been a problem.Put new improved seal in.Easy part.Reassembled. Springs and clips hard.Washing again and quiet.Wife happy four days later.Old guy sore.All done with outer tub in machine.Estimated savings Big,Big,Big.Getting big steak dinner and big kiss.

after getting the washer apart and notice that the inner andd outer bearing were bad, I had to beat out the bearing because they were rusted in. after getting the bearings out the washer went together quite easily. It runs like new again.

Followed the PartsSelect video for the seal replacement, which was step by step and spot on, I just had to add the bearing replacement part myself. Once it was dissembled I drove each bearing out by tapping them with the hammer and drift. My model had no bearing retainer ring. I did not remove the outer drum from the washer. Clean the aluminum hub real well, scrape it with a utility knife to remove corrosion, wipe with a solvent soaked rag, etc. I disagree with other methods ive seen while researching, like a wire brush in a drill, because you will remove aluminum material from the hub and the bearing wont fit as tightly as designed. tap in the rear bearing til fully seated. I did the rear first because gravity then held the spacer in place. Set the spacer in place, noting that one end is "flared" to a larger diameter, so it seats against the larger race of the front bearing. Align and start the front bearing in place. The spacer needs to align with the bearings so it bears against the inner races of the bearings. So to hold it in place I rolled up a piece of light cardstock, slid it thru the spacer and bearing, and as it "uncoiled" it aligned the spacer. Pretty well. I did have to tap the spacer a little with the drift after the bearings were in, but just a little. After that, back to the video for the seal and reassembly. Only other comment I have is to locate the bearings early. I ended up going to grainger for one and Napa for the other. And no one could seem to cross the "DU" part of the original NGK bearing. The DU means it just has seals on both sides. Pretty standard stuff. That could have been easier. Also hold off ordering extra parts. I have found PartsSelect is really quick getting stuff out. I ordered an inner drum because i heard from other research that that could cause the banging noise. My banging noise was from one bearing disinegrating and the balls breaking up inside the hub. Shipping the drum back cost 70. UPS wanted 160. So that could have gone better, but I didn't want to let the machine sit too long. Next time I'll let it sit a couple days.

Removed tub replaced bearings. Put in new seal. Be aware drawing on instruction shows seal cup instaled from wrong side of seal. Other wise went well. Got bearings from McMaster Carr.

Using online disassembly instructions removed and replaced front and rear bearings. Then attempted to install the seal kit that was purchased online from partselect. Com. Was supposed to receive both seals plus lubricant so that no matter which seal I needed I would be covered. The kit I received had 2 seals that were identical. . . I needed, as it turned out the early seal kit, but unfortuneatly I had 2 revised kits. Of course I tried to assemble one but it just won't work. The seal kit must be the correct one. I didn't give up. I ordered another seal kit online from appliance partspros. Com and received both kits as advertized. . . One being the early version plus a small packet of grease along with all the other required loose parts and was able to complete the repair. The second time around proved much easier because of the experience factor.