A23CDW Maytag Washer - Instructions

Removed top. Removed agitator and tubs . Replaced seals and reassembled.

Did repair as instructed by video, I'm 74 years old if I can do it anybody can!

My washing machine would only run hot water. Told my husband and we were ready to call the repair man when I suggested we try to order a part. So I Googled "washing machine repair". Clicked on the first sight I saw and 'searched 'no cold water' amd immediately saw explanation of our exact problem. The solution explained that MOST of the time the problem was the water inlet valve. So I ordered the part. My husband put the part on the machine and the process would have taken less than 10 minutes however the clamp was so rusted to broke and that required a trip to the hardware store. But I suppose clamp-life does not exceed 20 years. So mission accomplished and a great big thanks to all those who explained what they did to solve the problem!

Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.

I unscrewed the bottom two front phillip screws. Lifted the front panel at a right angle then popped off downward. Used a 3/8 socket to unscrew the two screws inside in the upfront corners holding the top to the sides. Pulled off the top bleach line.
Lifted the lid upward until it rested on the back wall. Unscrewed the water fill tube connected to the top side panel which to reach the inlet valve area. wrote down which color of the four wires went where. Unscrewed the back plate and disconnected the valve wires. Reversed procedure for installation. Cleaned other parts while I was in there. Installation went quick and smooth.

1. Unplug machine.
2. Removed front cover,(2 screws).
3. Removed top cover,(2 screws).
4. Remove hose at top (twist lock), loosen clap holding hose at bottom.
5. Reverse procedure, attach clamp at bottom, attach hose at top(twist lock).
6. Plug in machine, turn on (fill), check for leaks.
7. Re-attach top
8. Re-attach front.

After removing the front cover and tilting up the top of the washer housing, the area of leakage was obvious. I unscrewed the clear plastic injector housing, loosened the clamp, slid the hose off of the clear plastic injector housing, and removed the plastic injector nozzle and the rubber injector valve.

I then order the plastic injector nozzle and the rubber injector valve. After the parts arrived, I simply put things back together, and no more leak!

Note: When putting the plastic injector nozzle into the rubber injector valve, I used a little liquid detergent as a lube.

simply removed old motor and replaced with new

The three parts fit together to form one unit. As has been mentioned here already I'm not sure what purpose they serve. I'm also not sure how replacing them stopped the leak but it did. If it had not stopped I think I could have bypassed the valve entirely with a piece of hose or PVC and had it work just fine.

First thing I had to determine what was wrong. The machine had worked admirably for a 1980 model but over the last few years cold water input had reduced to almost nothing. There was also a slight hum during filling but it had been so gradual I really didn't recognize it as part of the problem.
After checking that the cold water faucet, hose and screens were okay I removed the front panel to see how water flowed inside the machine. I suspected the inlet valve on the machine was not working correctly so I looked on PartsSelect and found similar repair stories. I ordered one and it arrived in 2 days.
Repair was simple. Turn off hot and cold water and disconnect hoses from machine. Mine were on snug so it took pliers to get a turn started. Lay them in a pan to catch drippings. On the back remove the single nut above the inlet valve and lift to remove the panel. Remove the two mounting screws for the inlet valve. If needed rotate the electrical connections on the new inlet valve to match the old and transfer the wires. Remove the small output waterline and transfer it to the new valve. Mount the new valve to the panel and resecure the panel to the machine. Snugly attach the hot and cold water lines. Turn on the water and after checking for leaks you're good to go.

Removed the bottom belts to inspect. Belt for tub was well beyond it's service life. Belt for pump was OK. ordered the pair and replaced. When the washer was started the agitator still did not move. With power off I grabbed the agitator and pulled upward a few times then twisted it from side to side a few times. No change. Then I did the same with it with powered up ( a bit dangerous ). The agitator then ran OK.

Could not repair. The gearbox on the agitator was broken and that kept the agitator from working. Do not assume it is a belt problem on a washer built in 1987.

unplug machine ,shut off water supply,Removed 2 lower front panel screws ,raise panel upward "hinge type motion"and removed , Remove 2 self tapping screws from under front corners, removed liquid bleach tube from upper connector ,raise top toward back of machine , place prop "piece of wood" to hold top up,removed 1 screw attaching injector ,now replaced injector assy and install with new hoses and clamps. then assemble in reverse order

Installed drive and pump belt.. very very simple. only tool required was a screw drive to remove front panel of the washing machine.

Replaced both the drive belt and pump belt in less than 10 minutes. Maytag has the easiest machines to work on.