MVWP575GW1 Maytag Washer - Instructions

Using the IPB I removed the upper assembly to gain access to the cogs. Turned the assembly over and incerted the new parts and reassembled the pieces in reverse order.

1. Lift the softener dispenser up and out
2. Lift up the plastic cap underneath
3. See bolt...use ratchet with extension to loosen and remove bolt
4. Remove whole agitator by simply lifting it up
5. Place agitator on floor and separate top from bottom agitator by simply pulling apart
6. See 4 plastic cogs that spin the agitator. Like mine they are probably completely worn/stripped.
7. Replace old 4-cog set with a new 4-cog set. They are small and inexpensive parts! I did this and our machine is working just great!

This also gave me a chance to clean the agitator thoroughly!

first remove the cap on agitator(softner),then pull out inside cap (small cover inside),loose bolt in center (you need a 7/16 socket with a long extension) after that pull up the whole assamble out of the washer tub,hold bottom part and pull up agitator ,turn up side down to take out the cogs and holder, replace with new ones and go back on the instructions.

I took a socket and removed the agitator bolt and cover which exposed the cogs. I cold see the cogs were stripped. I changed them and everything works fine.

FIRST I printed the directions from an online DIY stie, then removed a single bolt from the center of the agitator. I dismantled the agitator, replaced the dogs, and used to printed page to help me reassemble the agitator. I then replaced the bolt. It's VERY easy, but you need the pictures to be sure you've put everything back in the correct place.

remove top of adigator and remove bolt. remove plastic clip and cogs.replace in reverse order.

We ordered the dog Agit clutch and within a few minutes I had a new washer. It started agitating a lot faster.

Removed the four worn agitator directional cogs and replaced them with new ones

Removed agitator according to instructions, although upper and lower agitator did not want to separate. I used a steel rod and hammer to separate them by hitting lower agitator where bolt goes through. After removing and replacing old cogs, cog holder had to be tipped upside down to insert in agitator. I used a small dap of toothpaste to hold retainer in place while I inserted it in agitator. Works great now.

I went on line to find out how take the adjetator apart. You just stand on the adjetator and pull the top off. Very simple. Once that wss apart I cleaned the dog area of dirt and old pieces. Install new dogs and put it back together. I was trying to make much harder than it was. Piece of cake.

Removed the bolt that holds the agitator in place..pryed the metal ring that holds the agitator dogs in place..replaced the old dogs with the new ones..old ones were broke off so I had to figure out what direction to install them by assembling everything and making sure that the dogs would catch the teeth on the part that surrounds them..reassembled and then the machine wound agitate properly..but then discovered that the direct drive clutch was not working keeping the drum from spinning..so I replaced the clutch but that's another review..

THE INSTRUCTIONS ARE ON THE SAME SITE AS YOUR PART WHITCH MADE IT SIMPLE

I followed a repair video on YouTube It is easier to disassemble the agitator and replace to cogs The hard part was placing the top part of the agitator back onto the bottom parts, after I replaced the cogs. i use a flashlight to help see where the two separate pieces of the agitator need to be to connect the back together properly ( top agitator & bottom agitator). Once this sep is completed you have to place the whole agitator and line it up on the agitator rod. Line up the groves as much as possible. Turn the agitator slowly until it slides into place. Then use your socket wrench to tighten the screw. The screw is the last step to attach the agitator back onto the washing machine. Then replace the cap, to keep water from going down into the washing machine. Then replace the fabric softener dispenser. Now you have a great washing machine. I am a women and did this repair by myself.

The repair went smoothy except for removing the screw that holds the upper agitator part from the bottom agitator. Once that was removed all went smoothly. Considering my washer is 17years old, I guess I should be happy that was my only problem. I followed the directions of the repairman in the video that was provided by the web site. Most of my parts matched his parts :). My husband was very proud that I repaired the washer and was able to diagnose the problem. Thanks for helping me save some $$$$. I'm pleased and am very happy to have solved the problem on my own. My husband teases me about hanging a shingle. Thanks, Zina

removed the agitator and melted the retaining clips to loosen the retainer cover for the cogs. went simple after that.