MAV7600ACQ Maytag Washer - Instructions

Placed the washer on 2 brick under the front. Removed the belt, used a straight blade screw driver for the lifting of the top off. reoved 2 bolts off the face and removed the screws of the water pump. Water pump was messy with smelly water but a bowel and a towel helps. Placed the pump on, reversed the tear apart...placed the belt on the bottom. Removed the brick under the front. Hooked up the water supply...plugged in and did a load..it worked perfectly....Thanks!!!!

There are two clips that hold the top of the washer down. Releasing these clips allows you to lift the top; it is hinged at the back. Then remove two screws holding the front panel and remove the front panel. The tub to pump hose is easily accessible. It is held in place by a hose clamp at each end. Use pliers to squeeze the clamps and remove the hose. Replace with new hose. I re-used the original clamps.

I felt extremely confident when purchasing the part because I say three diagrams which clearly showed I was ordering the correct part. 0. Drain all of the water out of the machine. 1. Remove the rear panel from the washer. 2. Use the pliers to disconnect the hoses from the pump. 3. Remove the three screwa from the old pump. 4. Support the washer with the block then take the belt off pulley. 5. Remove old pump. 6. put new pump in place then reconnect the pulley, you can remove the block.. 7. Install the three screws for the pump after you tighten it up by placing the pump over ther correct screw holes.. 8. Reconnect the two hoses using the clamps you removed. 9. Secure the rear panel and screw in place. 10. Wash clothes. EASY FIX!!!

The hardest part of this is the springs. The best way to disconnect and reconnect was to tilt the tub towards the spring I was trying to work on (thus putting less tension on the spring and cutting down the distance). I took a large boot and jammed it into the oposite side wall to hold it in a tilted position before I disconnected the spring and then redid that to reconnect using a vice grip wrench. I replaced all three things, snubber, brake roto and stator and it went back together very easily. The key on the pully shaft was hard to reattach but there was a trick to that as well. The shaft has to move up slightly to slide ring on so you need to have something under the tub to help raise it. After that was back together it was 15 mins. to finish and now the washer is running like new.

Remover agitator/Auger assembly. Install new agitator/auger assembly. Washer still would not agitate. Called repairman and found the transmission was bad. Fortunately transmission was still under warranty. 10 year warranty on transmission.

Removed upper back cover to expose the timer, the whole panel could then be tipped foward which made it easy to work on.
Removed the dial knob on front by popping off the cover then pryed up a smaller plastic button used to hold the knob in place.......knob slid off.
Disconnected wire harness from the switch.......had to pry up the snap tab that holds it in place.
Had to remove a small electrical board attached to the back of the timer......used screwdriver to pop it up and out (gently).
Removed one hold-down screw, lifted a little lock-tab and slid the unit to the left and lifted out and replaced.
I'm sure I forgot something.........but the whole thing was pretty easy to figure out .

I removed the rear panel of the washer, and removed the lid switch assembly. Then, replaced the old one with the new lid switch and plunger. Put the rear panel back on the washer, and started washing clothes again!!!!!! I think a monkey could have done it....

I did what anyone could do, remove the screws and replace the part. The part just came apart during installation. If I were Maytag, I would replace the part free of charge.

Found a website that showed how to open the lid. Lifted the lid and checked the solenoids. When hot was disconnected, got cold only. Multimeter showed hot was being continuously energized regardless of temperature selector switch position. Removed back (5 or 6 screws) and found the circuit diagram. Studied it and determined that the switch or analog card had to be the problem. Took digital pictures of everything to aid in replacing wires pulled for trouble shooting. Pulled temp selector switch (pushed in a couple of tabs). Disassembled switch and checked all contacts. Working fine. Nothing left but the temperature board. Determining correct revision was difficult. Found a website that said, "first numbers of serial are revision number. Pick card with highest revision number lower than your model." Replaced card and everything worked as designed. Every wire was labeled and every wire bayonet was labeled so I didn't need the pictures, but I felt better having them.

Took a screwdriver and pried up the top of washer, then reached in and unscrewed the front two screws that allowed the front to be lifted off.
Removed two screws on lower right side that allowed us to pry open right side of washer. There are six springs along the bottom of washer that keep the tub stable and keep it from bouncing against sides while in spin mode. One of the springs broke and needed to be replaced. Off course it was the one that was in the far back and the hardest to get too. But by prying open the right side it was reachable. The wife pushed against the tub to make the spring stretch a little less but still was too difficult. We took the advice of another home repair guy and put quarters in the spring (about $1.75 worth) to make it stretch out, then it was simple to connect the two ends, remove the quarters and voila....it was done. Screwed theright side back on, but the minimum order on the springs was six and the others seemed fine, we just put the other five inside the washer cabinet, replaced the front panel, reset the clamps on top of the front panel, slammed the top down and we were back in business. The parts including shipping was a little over $10.00. So I am sure we saved at least $140 repair job.

Removed the front panel, Removed the belt from pump in the back of machine. Removed the pump from the back of machine, Put the pump in reconnected the belt, Replaced all the screws. My husband did the repair work in a matter of 45 minutes. Machine works fine now. The part came when I was told it would. I am very pleased with your service.

The repair it is simple the problem was to figure it out, I did some research on this kind of problem and everything was pointing to the timer so I used a philips screw driver and a nut driver to remove the backside of the control panel,but first don;t forget to unplug the machine, I have to pry off the knob top cover and remove a plastic clip to pull the knob after that you can unplug the electronic board connector and the timer connector,remove a couple of screws amd the timer is out, installation is the reverse of removal.

For safety I Unplugged the machine
Tipped machine back and removed the belt. Rotated the motor by hand and all is well there. Rotated the water pump by hand and a grinding sound appeared. I Let the machine down . Using a hard object , 1/16th of an inch thick, I slide it between the front edge of the lid and the front panel unlocking the clips ( one on the right side and one on the left side ) holding the lid down. I then tipped the lid up and removed the 2 screws holding the front panel on. Lifted the front panel off of the clips on the bottom end of panel. Using a nut driver I removed the 3 bolts holding the pump to the frame. Then with a pliers I removed the clips holding the 2 hoses. With a pan to catch the water I removed the hoses and drained them into the pan.
I then took my machine model number and went to the internet in search of a new water pump. After checking several sites with no success, I come upon the site for PartSelect.Com. With the excellent search method on the site I was able to quickly find the part I needed. I placed my order (10pm) on a Tuesday night and a short time later I received an email letting me know they had my order. On Wednesday I received an email letting me know they had shipped my order. On Friday the order had arrived.
I removed the new pump from the box and inspected it . Every thing looks great. I placed the pump into its mount on machine and bolted it down. Attached the 2 hoses, put the front panel back on and tipped the top down into place. Pushed machine into place, plugged it in and fired it up. I now have a quiet running machine again. Thank You to PartSelect.com for the quick response to my

First I took the front shield off, then I took the motor off.

tip washer up on wooden blocks.remove drive belt.remove "E" clip from tub drive pulley and remove all the parts.Install new parts in kit as per instructions.machine works great!