MAH7550AGW Maytag Washer - Instructions

Thanks to Partselect's accurate parts' lists, and installation video, along with others' posted installation trials, gained confidence to attack problem on my own (coupled with repair (or should I say, "replace")men's advise to trash machine). Bearings had basically disintegrated, causing inner tube to be out-of-alignment, and rub against outer tube. Would just like to add to what others' contributed, that I found Plumber's Tub Drain tool to work very well at knocking-out larger front bearing (was perfect fit to ID of bearing). Had to Dremel cut out rear bearing, but quite accessible from rear of machine. Otherwise, alot of cleaning from 13yrs. of useage. Thanks for everyone's assistance!

The replacement was not complicated. It took me more time because the details are not in the videos and I had to do it twice because I didn't get the seal on correctly the first time. I used the Neptune videos available on you tube for the basics. Use the "inspecting front door lock wax motor" video for a start, but be sure to take off the top front crosspiece also for easier access to the spring that tensions the seal retainer cable. You don't have to disconnect any wires, just lay the door lock assembly gently to the left of the washer. The old seal comes off very easily, using the front loader door seal video. My washer was an early one without the drain tube so I had to get the drain tube and clamps separately and drill out the tub nipple to the left below the seal. I used the biggest drill bit I had that fit inside the nipple. The tub is plastic and very easy to drill. Most of the plastic shavings will come out toward you if you drill slowly and don't push too hard on the drill. I also used my shop vac to try and get out any other shavings. I used dish washing liquid as a lubricant to help put the seal on and used too much. It doesn't take very much. The spring that tightens the inner seal clamp/cable was very hard to attach and it did require two locking pliers [vise-grips] and quite a lot of effort. You have to hook one end of the spring to the cable that wraps around the seal, hold the other end of the cable with locking pliers, the free end of the spring with locking pliers, and stretch the spring to hook it to the free end of the cable. There are some other methods described in various forums and one of them might work better for you. When I was an auto mechanic we had a special tool that helped attach springs like this on drum brakes. I was sure wishing that tool was still in my tool chest but it was not. This was the most difficult part for me, getting the cable and spring all in place and stretching the spring without dislodging the seal and having to start all over.I didn't get the seal aligned correctly the first time and had to do it over after putting ever thing back together and washing a load of clothes. I could have avoided that by carefully inspecting the seal before I put everything together. When you put it back together the end of that red or green nylon line that looks like weed eater line goes under the soap/bleach dispenser bezel on the top so you can manually open the door if the wax motor goes bad and it won't unlock.

I followed the video for the installation. I did find that installing the spring was no way as easy as it looked in the video. Otherwise, OK.

Basically the problem was the bearing replacement. Although you cant get them on PartsSelect, I got the seal kit on the site. The seal kit is easy, the bearings took two days and an air hammer to extract them and a big hammer to get them back in. All in all it was worth it,

This is a stacked Neptune washer. You must take the door, front covers of the machine, plus remove the light and wax motor section to the side. You must disconnect the bleach and softener dispenser connections near the bottom of the washer to get the front portion off so that you can get to the boot. Catch the excess water in a pan to avoid getting the electrical circuit board wet. Take the boot off. This is easy, but the spring that holds the small cable around the boot is a bit tough. You can do this with the needle nose vise grips. Place the boot on the tub first making certain that the small notches in the boot line up properly onto the washer ridges. I had to use a 2 X 2 to pry the tub down so that my friend could get the boot lined up on the tub. Some stretching of the boot is required. Place the cable around the boot on the washer and use a strong mason's cord or similar cord and tie the ends of the cable as tight as you can get it so that the cord holds the cable in place. Place one end of the spring into the cable end and taking the needle nose vise grips pull the spring until it can be placed into the other end of the cable. When finished, take a knife and cut the cord and pull it out. The spring is very strong so it is difficult to pull it into place. Since I am old, I had to enlist a friend who is an appliance repairman to get the spring on. That is the most difficult part. Lastly, you get some dish soap and place around the inner part of the boot where it fits onto the other section of the washer so that you can get it on easily. Reassemble the parts and everything should work OK. Don't remove the plug at the bottom of the new boot unless your washer happens to have the drain connection.

Replaced the belt and motor isolators. Watching your video made it very easy.

I bought the new Lip Seal Kit thinking that the sound I was hearing had to do with it sticking inside the drum at the end a rotation in either direction. We had replaced the outer drum a few years back when the bearings went. Believe me, you will know when your bearings are going. It sounds like you are in the same room with a jet engine. I knew this sound was not from the bearings. I had the washer apart in about fifteen minutes...and yes, I am a 125 lb. female...so ladies, it is not an impossible task. I have taken that washer apart enough times before that it is no big deal. Just make a mental note as to how it goes back together....if all else fails one can look at diagrams online. My husband just stood there and said "nice job honey". After I got the old seals out and the parts cleaned up, I turned the bearings to make sure they sounded smooth. A-okay. I installed the new seal and smoothed molycote on the spider shaft; replaced the drum, front panels, etc; tightened the pulley with a torque wrench, belt on, etc. and.....turned on the washer. The sound is still there. Sooooo, I am fairly confident that it comes down to the belt and the motor isolators...mostly the isolators...belt is pretty secure. I am changing those tomorrow. Found someone on youtube with the same problem...only far worse...and a response posted said it probably was due to the isolators and belt. Our seal wasn't too fried, but I guess that it isn't a bad thing that I changed it anyway since it has been a few years and they do fail resulting in bearing damage. Better to catch it now. As for whether my machine is worth fixing at its age, I went shopping while this was going on and I don't trust anything out there to not have a multitude of problems. At least with my current model...that still looks like new btw...I don't have a learning curve to deal with on how to take it apart. And a great big shout out to my father who taught me how to dig in my heels and get my hands greasy!! Update: Replacing the motor isolators did the trick. Put on a new belt too as long as I had the back panel off again. Running like a champ!!

removed the door &the top took the tightener off the bellow took old one out put new one on and clean all parts and put it back together works like a new one love it.

I watched the provided video that EXCELLENTLY showed the replacement of the part. Then I was able to complete the task with no trouble at all

Received motor control board and new motor in one day - awesome! Took off front panel, disconnected power and water supplies. Disconnected wiring connections between motor control board and motor. Removed old control board. Removed back access panel. Replaced old motor with new motor. Put rear access panel back on. Installed new motor control board. Reconnected wiring connections between motor and control board. Put front panel back on. Reconnected power and water supplies. Done! The hardest part was moving my stack washer/dryer around to get at the rear access panel. I ended up putting the entire unit "face down" to make it easy to get access to the motor. Instructions that came with the motor/board kit were easy to follow. Only down side - I believe my old motor still worked fine. I'm sorry I had to replace it to replace the motor control board. Machine works great now.

Ordered a new inner panel and had my son in-law put it in for me. He is a mechanic so it was a quick an easy fix.

I went on your web site and printed the instructions given by the first entry after the product description. I had called my friend who is also a handy man and he did the repair very quickly [I helped very little]. The directions were very complete and very simple to follow. MAH5522BW

I thought for sure the washer was toast! Thankfully, due to your website it was an easy 26.00 fix. Husband took care of the repair in about a half an hour. He did not encounter any problems with the fix and it's running like a charm!

The machine had the old style boot drain hose with built-in bellows. The constant flexing of this tube caused a small crack in one of the bellows that gradually increased in size over time, causing water to leak into the bottom front part of the machine. Repair accomplished by removing the door (crosspoint screws), the retangular panel above the apron over the door, the apron above the door (5/16 socket), and the front lower panel (crosspoint screws). Pliers used to open the spring hose clamps, old leaky tube removed (re-use the rubber clearance washer that is on the tube). New tube installed easily, then panels reinstalled. 10 minutes total.

removed front of washer. loosened two hose clamps. replaced hose. tightened clamps. replaced front cover.