PAV2300AWA Maytag Washer - Instructions

No need for the Maytag repairman anymore. Video supplied was all that was needed. Could not have been easier.

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

removed rear acess panel and used pliers to remove leaking hose then reinstalled new hose..

remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three screws back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.

The repair was easy. I had to unscrew on bolt, place the agitator assemply on and screw the bolt back down. Simple , Sear was gonna charge 175.00 just to ship the part. I got the part for $57.00.

Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom

took back off washer with nutdriver, pulled wires off by hand, ( was unplugged ). pliars used to remove hose, regular clamp put back on. reinstalled back plugged in, tested water,,,, done

Followed the excellent utube instructions you provide. Piece of cake when I followed the video. The rear springs became much more difficult because my model does not have rear access panel. They were the only stuggle. Thank you for doing the repair videos

Unplug power cord; turn off hot and cold water supply; remove water hoses from machine; open top of machine by prying lid open; remove two hex screws holding water inlet valve in place; remove hose from top of old water inlet valve; remove 4 wires; connect bottom set of wires (red and white) to new water inlet valve; reinstall water hose to top of new water inlet valve; install new water inlet valve onto machine using same hex screws; connect remiaining red and white wires; install hot and cold water hoses to machine; turn on water supply valves at wall; reconnect wall plug; turn water type selector to cold, pull out timer and watched the water flow full-force for the first time in 2 years! Have wife give you a hug for saving cost of new washing machine!

Disconnected the power plug. Turned off the hot & cold hose water supply. Put down old bath towel. Disconneced hoses from machine inlet valve. Opened entire top for access to electrical connections & fill hose. Replaced inlet valve, new wire connectors. Replaced the hot & cold water hoses.

This was my first washing machine repair.

Took off the back plate. Looked to see where it was leaking. Squeezed the clamps on top and bottom to remove from hose and pull hose out.

Brought unit out to garage so I would have room to work on it. Popped the top off, removed two screws to remove the front panel, removed back panel also, since there was no way I was going to the trouble of dis-assembly to get to the snubber without changing those 6 springs also - and you HAVE to remove the back cover to access all 6 springs.Removed belt and level and drain hoses- tub came right out. Loosened those 6 screws without removing them and pulled old snubber out- very straight-forward. Spent 10 minutes just comparing the old and new snubbers- I saw that there's a "ridge" around the inside of the new part that is gone on the old snubber. Sprinkled some corn starch at base of unit where the new snubber will fit (Great Idea someone had!) After everything was re-assmbled, I noticed the tub was now nice and tight when I grabbed it to move it. Before, it took no effort AT ALL to move it all around. Did a test load with some laundry the wife had stacked on the drier. Imagine my disappointment when I heard loud knocking inside when it started to agitate, but not while it spun!
Got all my tools back out and took the wet laundry out to take it all apart again- found the wife's heavy glass vase had been hidden in one of the towels. Re-tested- everything works GREAT!So far I've changed the drum seal (hardest) and the waterpump (easiest)- thi springs and snubber was alsmost as easy as the pump.
Above average shipping from Parts Select also- very helpful and efficient people on the phones.

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

Back of this washer did not remove, so we had to go in through the top--more restricting space. As you remove the old electrical metal contacts (two each of white and red), pay close attention to where they connect properly. Best to mark them so as not to confuse how to place new contacts. Also, we disconnected a white plastic hose on opposite side of top which determines load size and amount of water, so be sure to look for this.

Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was done, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.