MAV9557EWW Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gerald from MADISON HTS, VA
- Parts Used:
- WP35-6780
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Pump locked up so washer stopped working
Removed inspection panel on rear of washer. Pump right there. Removed inlet and outlet hoses with pliers on squeeze clamps. Three 3/8" size self tapping screws were removed and old pump came right out. Reversed process with new pump from this site that fit perfectly. New pump was an upgrade factory part that mounted inside washer without a mounting plate as the old one did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from Elk Grove, CA
- Parts Used:
- WP35-2328
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
I had water leaking from the top of the tub.
I opened up the top of the washer which exposed the tub, I took the top ring off the tub and under in side of the ring is the seal. Took the old one out and put the new one in. The old seal was completely wore out.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.
It was real easy.
Finding the part is usually the hardest part, but thanks to Parts Select finding the part was the easiest part of the repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sam from Clinton Twp., MI
- Parts Used:
- WP22003483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Belt was squeeling with a burning rubber odor
Diconnected water lines, layed washer on its side, spun pulleys and pulled belt off at the same time, put the belt on in the same way. VERY simple
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Edwin from Eagar,, AZ
- Parts Used:
- WP35-6780
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Leaking Water Pump
Pulled wahser away from wall, unpluged, removed screws from rear access panel, removed hoses from water pump, used towell to absorb excess water still in pump and hoses, removed drive belt, removed screws securing pump, removed old pump replaced it with new pump, cussed a little when replacing hoses, repeated steps in reverse order, checked for leaks.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Nicholas from BROOKLYN, NY
- Parts Used:
- WP21001950
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
Washer motor
Replace the motor in 25 minutes, my repair guy said it was not worth the time , I got this motor for less than $150. And save my self over $600.00, this was incredible.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lester from Elk Grove, CA
- Parts Used:
- WP22003483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Belt was slipping, belt particles on the floor
I removed the screws to loosen the belt, took off the old belt and put on the new belt. Tightened it up and has been working ever since.
Thank you, Lester
you guys ship faster than anyone else. One day I order the part and a day or two later there it is. :)
Thank you, Lester
you guys ship faster than anyone else. One day I order the part and a day or two later there it is. :)
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- noel from new ulm, MN
- Parts Used:
- WP22003483
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Getting real loud squeeking, wouldnt spin water out
I knew it was the belt because of all the noise it was making. I ordered the belt and it arrived real fast. I pulled the washer away from the wall and tipped it back at about a 45 degree angle against the wall so I could get under it. I propped it with a bucket. I then pulled the old belt off and spun the new one on. Real fast & easy.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SONY from CONCORD, NC
- Parts Used:
- WP35-6780
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
The washer was making a fine squeeling noise that created a foul burning odor
Took the washer outside, turned the washer on its side to expose the bottom panel. Removed the old water pump (three screws and two hoses. Replaced with new water pump and connected all fittings. Real easy to do. Washer runs great now.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from New Braunfels, TX
- Parts Used:
- WP22004333
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver
leaking water inlet valve
Parts look up was simple. part was priced right. part received in a timely manner and was as advertised. installation was quick and painless.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jane from Delray Beach, FL
- Parts Used:
- WP22003987
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Broken knob
I just needed to replace a knob because the original, (plastic) broke. What was great was how soon I received my order, just a matter of a couple of days. I wish I had ordered several as both my washer and dryer have the same ones (five in total) and now another one as broken! I think I will order three or four move.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- JERRY from LEXINGTON, NC
- Parts Used:
- WP22003285
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Washer Was Leaking When Water Was Pumping Out
Took a putty knife and raised the top,then took two bolts out, then pulled front panel off. Took hose off from the tub to the pump,and put the new one on. It's working fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Huston from columbiana, AL
- Parts Used:
- WP22003285
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
water in the floor
take a butter knife and pop the clips loose on the front between the lid and the front take the two screws loose on the front in each corner remove the front cover and you will see the hose take the clamps off and replace the hose
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from Florence, AL
- Parts Used:
- WP25-7220, WP22004333
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Hot water valve leaked by and then at last wouldn't open
Easy repair replacing the water valve assembly. Good advise from other posts helped much.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mark from Cadillac, MI
- Parts Used:
- WP22002751
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Lid hinge was broken causing lid to fall off when opened
Opened the lid and snapped hinge in to place. The part was an exact match and the job went flawlessly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BEN from DEXTER, MI
- Parts Used:
- WP22004333
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
would not stop dispensing water at any setting
followed directions you gave. Simple
Was this instruction helpful to you?
Thank you for voting!