LAT9304EGE Maytag Washer - Instructions

Followed the directions posted by another user. His tips were very important and helpful. At first we only ordered parts where it was leaking, then decided we might as well change the remaining parts as recommended by the other user in his description. This is the FIRST issue we have had in 19 years of use. Ordered the parts, received them quickly and correctly. Installed them and it works like a new machine. This Maytag will probably last another 19 years.

all went well until testing. tub level did not shut the water off, caused a spill

Unplug machine and remove drain hose clamp and hose from rear of the machine.Using Phillips head screw driver remove the 2 screws from the lower front panel of washer. Lift and remove front panel. Using a small socket, remove 2 screws from the inside top left and right of machine which secures the machines top cover and lift cover up (use duct tape to secure washer lid from opening). At the inside rear top of the machine is the Siphon Break Connector. Loosen clamps, remove old Siphon Break Connector and install new one. Reinstall top cover, front panel and then drain hose.

new replacement water pump leaked where plastic housing upper and lower halves were bonded, presumably with glue. As a quick fix I wrapped pump with some 3M 4411N sealing tape. Seems to have stopped or really slowed leak. I was going to get another new pump but now worried it will leak as well so going to see how long tape fix works..

Well I looked on line to see if there were any similialtys to my problem and followed what they had done on their washing machines. I replaced the water pump,the slide control below the motor,and the lid switch.None of these items worked.I called a tech.and he informed me that it sounds like the transmission is bad ,he is coming to my house tonight to take a look at the machine.

Top came off quickly with socket wrench. Removed gasket in about a minute. Spent 45 minutes getting grime ( soap and lime) off of top. Took five minutes to replace gasket.

Haven't been able to get front back on. Clips go on side rather than top. Found missing clip for which new one was purchased in transmission. Still haven't gotten front to stay on. Clips keep springing out.

Remove the rear panel covering the control panel. Remove the two screws on each side of the upper control panel. The top removes with gentle (or not so gentle) taps toward the front of the washer. Lift the upper away but be careful of the attached wires. Top must be removed or switch cannot be removed as it cannot pass the cycle selector. Note the wire positions and colors to the switch assembly, remove them, and loosen the screw holding the switch assembly in place. Tilit assembly up like opening a book and lift up and away from the washer being careful of the lid switch actuator below. Replace with new assembly, making sure actuator is positioned to activate switches, and reattach the same screw. Reattach wires to appropriate places, replace top control panel and reattach screws, replace rear panel.

Replaced the lid switch assembly, works like a charm.
10 minute repair, 4 screws for the front panel, one for the switch assembly. Be careful not to break the plastic tabs that hold the right side of the assembly. As someone else noted, adjust the assembly front/back in the screw slot so the switch activates properly for open/close.
Fast shipping, great price, thanks Part Select!

1. Remove front panel with phillips screw driver.

2. Remove hose from drum and exit pump

3. replace hose with new one (used some silicone grease on hose)

4. Tightened clamps with nut driver

5. ran a couple loads of wash to check for leaks

6. found none

7. replaced front panel - Job done

Followed above listed advice on replacing

Repair not that complicated. Remove front, lean top back, remove agitator, remove special nut, remove inner tub, remove seal. Clean shaft and seal surfaces. It is highly recommended to the spanner wrench to remove the special nut. It appears one can do it with a punch and hammer, but the nut is too tight, and corroded from years of water exposure. I believe part number is TJ90TB123A, about $15. Watch the video on this web site, very good.

I saw on internet that it was the lid switch and how to fix it. On this machine I have replaced timer and belts, machine is 22 years old.
A bowling friend of my father, was a Magtag repairman and salesman. For years showed me how to fix my Sears washer and dryer. When he sold me a Magtag washer and dryer, he said it was a great machine.By the way my dad worked for Easy Washer in Syracuse, They invented the spin cycle, ask Whirlpool.
ED

Hi there,
I received the parts from you in short period of time,
take its out 4 screw with screw drivers,
Open the pannel, unscrew one nut with nut driver, take it out Lid assembly
I put it in myself, It worked wonderful,
I do appreciate your service in " Do-it-Yourself" system.

Thanks,

Harry Lin

Two screws holding top, unhook wire conector. remove cabinet,replace switch. Reassemble.

Very easy, and simple. Replaced part that was sent. It was a simple process, open control panel, unplug machine. Unscrewed the old part, attached the new part and starting working right away. I am very impressed with this company and the speed they shipped the parts. Will continue to use if needed and tell everyone about this site.