7MMVWB855EC2 Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Walter from KINGSTON, NH
- Parts Used:
- W11417461
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
Washer started drain cycle on its own. No lights, nothing worked, controls did not work.
Although I thought it was the electronic control panel it ended up being the front control panel with the dial and buttons. Apparently this part has the timer in it.
An easy swap just copy what is there. Remove the screws from the back of the control panel area. You need a putty knife about 3/4 inch wide to slide under the top control area on either side to release the spring clips, give the knife a little tap in and shake the top loose. If you look from the back you can see the spring clips.
An easy swap just copy what is there. Remove the screws from the back of the control panel area. You need a putty knife about 3/4 inch wide to slide under the top control area on either side to release the spring clips, give the knife a little tap in and shake the top loose. If you look from the back you can see the spring clips.
Was this instruction helpful to you?
Thank you for voting!
Non agitator pulsating action ceased
Ordered the parts and followed You Tube DYI clip. This 3YOMaytag top loading washer has had a motherboard replaced and now this. It all works fine for now, I cannot imagine what the appliance tech would have charged. Maytag is not what it used to be.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from LANCASTER, SC
- Parts Used:
- W10902814
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
washer plate would not agitate
after watching a video i ordered the part. removed the old part and installed the new wash plate using a socket and ratchet.
now washer works like new
now washer works like new
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from East Northport, NY
- Parts Used:
- W11130356
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Sides of washer dented out
Replaced Suspension rods removed 3 screws on back of washer, lifted the top, Removed suspension rods and and replaced all 4 on drum.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Stephanie from INDEPENDENCE, KY
- Parts Used:
- W10752187
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set
the impellar mechanism wore out so stopped aggitating
Popped the cap , used a socket to unscrew the bolt (it was stripped so ended up having to cut off bolt) Took off old impellar and replaced, installed a new bolt, replaced Cap and it was fixed.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from DREXEL HILL, PA
- Parts Used:
- W11244231
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers
Replace drain hose
At first I had to position the washer so I could get access.. after having it positioned, I figured it out. Getting the clamp fastened, I was done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Howard from Boynton Beach, FL
- Parts Used:
- 350930
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
Both outside door handles turned very beige
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you
Was this instruction helpful to you?
Thank you for voting!