PAV3240AWW Maytag Washer - Instructions

Problem fix after replace Snubber ring, I also replace suspension spring and driver belt due to the fact I'm already taking it a part

Looked up probable causes on PartSelect website. Determined that worn snubber ring and and weak springs were probable cause. Ordered parts on a Thursday. Parts arrived on following Monday.

Read several repair stories on the website. One story gave step-by-step instructions for disassembly. Very helpful since I followed this prescription. While waiting for delivery of the parts, I removed the tub and inverted it.

Removing springs was relatively easy. Did not remove snubber ring until new parts arrived, but replacing it was easy. I was very cautious about loosening the 6 screws and heeded the warning about the 200 pound spring under the cover.

Diagrams on website showing expanded mechanism of washing machine parts were very helpful for reassembly.

The most difficult part was installing the new springs, since they were quite strong. One repair story on the website suggested using coins to expand the new springs enough to be able to hook the springs into the upper slots and hangers.

I USED ONE OF THE MORE ACCESSIBLE LOCATIONS (AT THE REAR OF THE MACHINE) TO PREPARE EACH SPRING FOR INSTALLATION).

I hooked a spring in the bottom slot. I pushed a long heavy screwdriver through the spring's upper hook and the hole in the metal support and expanded the spring until I could insert 1/2-inch washers (about 8) between the rings. I prepared each spring this way for installation around the tub. With the washers in the expanded spring, it was relatively easy to use a pliers to lift the upper hook into the hole or hanger.

I decided to insert the spring next to the motor first since it was the more inaccessible. The remaining springs were installed relatively easily.

Reassembly was easy by following the reverse order of the disassembly instructions. I found the tub to be pretty heavy to lift, so when it came time to put it back into the frame, I turned the frame on it's side and inserted the tub from floor level.

I am very proficient mechanically but I believed I could make this repair without difficulty. I think that without the repair stories I had viewed on the website, it would have been more difficult. A spring tool would have been immeasurebly more helpful.

Researched "trouble shooting guide" Parts Select Website--

2 possible part failures - (1)--water fill valve inop-per Parts Select Web - 74 percent change of this unit failing.
(2)--pressure line fractured - 24 percent chance of this unit failing......

Ordered both parts from Parts Select -

Replaced water fill valve (possible solenoid failure--(although a little difficult to get at valve replacemnt was easy - total porcess took a little less than an hour).

Needless to say - problem solved with valve replacement, this machine should be "good" for at least another 5 years.

Thanks for your kind help and most important - the easy to use data...........

Spence Merrell
Dayton, Nevada

I used a screwdriver to release the front side of the waaher top from the clips and tilted the washer top back. I then released the hose from the water valve and took out the mounting screws at the back. Replaced the valve and hooked everything back up.

Leaned washer forward, removed clamp and old hose, replaced with new hose, reinstalling clamp.

removed 1 bolt with 1/2" socket, ratchet and extensionand pulled old part off, replaced with new part---less than 5 minutes total time

Removed entire cabinet from base, removed drive belt, removed suspension springs, removed tub and transmission together.
Removed 6 screws from brake housing to access snubber. Didn't have the special tool to compress the spring for reassembly, but used 3 longer screws to pull the brake housing back down...worked fine. Reinstalled transmission / tub and replaced all 6 springs. Reassembled cabinet. Unit spins great now...like new.

I'm not a washing machine technician but I did nurse a new Kenmore machine for 23 years and was ready for a replacement. Craigslist advertised a Maytag I was interested in and I bought it with the seller's assurance that it worked perfectly. It didn't and I went online to try and figure out what might be wrong. Clearly, the tub was traveling beyond it's design limit and I suspected a spring or two might be involved. Somewhere online, I found the illustrated parts diagram and then went looking for additional information. To my extreem delight, I came across a do it yourself repair video that demonstrated the procedure well enough that I was completely confident I could make the repair with little effort. That video was one of several service related appliance videos offered for free throughhttp://www.do-it-yourself-washing-machine-and-dryer-repair-help.com/index.html/ The final consideration was whether I could buy the replacement suspension springs and snubber ring for less than I paid for the washer. I found PartSelect and within minutes, I had the parts ordered. The parts arrived within 4 or 5 days, as promised, well packaged and in perfect shape. This morning, using the video as a final reference and the new parts, I completed the repair with only a minor hitch. Without the special spring tool used in the video, I struggled a bit with getting the new springs attached. That's where my wife came in handy (after all, she was movitated). Having her tilt the drum toward the spring landing made it much easier for me to stretch it into place using an adjustable locking plier. I actually enjoyed the whole procedure.

Pulled up the top of the washer and removed the lid hinge with a star tip screw driver. Realized that I also needed the hinge pins and had to reorder those. They should come as a kit.

Hired someone. Note: I purchased two (2) hoses and (2) clamps -- this is the third time I am replacing a cracked hose. The manufacturer needs to use better quality and more flexible material for hoses.

I obtained the parts on line and began to install these. I was surprised that the ease of my installation was great. Each part was held by one screw. I used a phillips driver and found the under screws easy to get to by pushing the inside clothes drum to the side. A total of four screws was required for the replacement. This repair was so easy that a normal non-trained person can accomplish it. Thanks Admiral.

Using nutdriver or screwdriver, remove metal panel from lower left side of back of washer to expose the pump. This is where the drain hose attaches to the washer. Use pliers to move the clamp off of the drain hose, then ease the hose off of the pump by wiggling it back and forth while pulling gently. Be careful to keep drain hose opening pointed upward until you can point it to a bucket, as there's likely to be quite a bit of water in it. Detach drain hose on other end as well (wiggling / pulling works well here; no clamp is used, so no pliers are required). Install new hose by reversing above steps.

I tilted top cover to remove front washer panel removed suspension springs to remove complete tub assembly to gain access to bottom. Drive pulley to remove snubber ring I performed the repair step by step as per your video. was dead on made the repair go smoothly. I installed the belt last tilting washer mechine back to gain access to undercarrige just walked belt on all three pulleys self adjusting then. made sure washer was level. Front to back side to side no rocking in any deriction My wife did four full loads problems gone I think all needed to be done to complete repair snubber ring , washer drive belt, & leveling machine all played there roll in putting washer back in factory working condition washer not a angery walking vibration nightmare

There is a small back panel about 14" square made to open for access to the drain pump. 3 screws for the back panel and 3 screws for the pump - Oh you do have to slip the belt off & back on, underneath the machine.

Looked under the symptoms .I had replaced the belt 2 weeks ago, so I ordered the drain pump. Pulled washer away from wall, removed water lines, unplugged electric. I removed the rear panel, found the old part right there, disconnected the in/out tubes, removed old pump, installed the new, re-attached hoses, reinstalled the belt over the 3 pulleys, re-installed access panel. Reconnected water and electric after placing washer back in position. Runs like a new machine!