Models
>
HA108
HA108 Maytag Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$33.20
Over time, the belts in your washer can either stretch out and sag, or become brittle and snap. When this happens, it can result in the belt losing its grip and will not be able to spin or drain the t...
In Stock
Order now and your part arrives by Jul 20
$83.71
This part has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor.
In Stock
Order now and your part arrives by Jul 20
$22.91
This lid or door switch kit helps ensure your washer or dryer only runs when the door is properly closed. It’s a safety feature that prevents spills and keeps your appliance working as it should. The ...
In Stock
Order now and your part arrives by Jul 20
This washing machine drain pump is intended for use with automatic washers that have been manufactured since 1958. The pump itself is made of plastic, though it does come with a metallic belt pulley.
No Longer Available
$134.02
This one-speed, 120-volt drive motor is designed for use in top-load washing machines and plays a critical role in operating the wash basket and drain pump. It powers the spinning and agitating functi...
On Order
This kit is part of the lid switch mechanism and will stop the spin cycle if the load is unbalanced. When you lift the lid, it resets the plunger and your cycle will resume.
No Longer Available
The timer controls most of the operations of the washer: water level, tub filling and emptying, length of cycles, and cycle setting sequences.
No Longer Available
Common Problems and Symptoms for HA108
Viewing 13 of 13Burning smell
Fixed by these parts
How to fix it
Will not drain
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Will not agitate
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Spins slowly
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
Spinning Issues
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Won’t Start
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
How to fix it
Shaking and Moving
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Brian from El Cajon, CA
- Parts Used:
- 205613
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Wrench (Adjustable)
Cold water valve only opened to a trickle
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outl
... Read more
et hose and pull off the outlet hose. I reversed the steps to install the new assembly and the total repair took about 10 minutes.
Read less
Was this instruction helpful to you?
Thank you for voting!
Drum would not drain and there was a banging noise when the drum spun
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools ... Read more and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools ... Read more and about 3 minutes to accomplish then resecured the front panel, pushed back in place and leveled. Complete repair from diagnosis to back in operation took less than 15 minutes.
Read less
Was this instruction helpful to you?
Thank you for voting!
Clothes would come out of the spin cycle still wet
First found out where the belts were by tipping the machine backwards and saw that the belts were intact but extremely loose. Ordered two belts (Drive and Pump) . Re-tipped the machine and in less than three minutes, had installed the new belts. I re-hooked the hoses to the back and the machine operated as if new.
Was this instruction helpful to you?
Thank you for voting!