MAV6000AWQ Maytag Washer - Instructions

I thought I was going to need to replace the leaking washer machine. Water was every where and after checking the main sewer drain was ok I lifted the washer and found the water pouring out the bottom when i put it on.
After finding out how to get the whole top open and the front panel off I was able to locate the source of the water leak on my washer machine. The cause was split in the plastic hose that goes from the tub to the pump. After the new hose arived I was able to replace it within 10 minutes. So far so good. Thank you Part Select.

These gaskets and seals were relatively easy to get to. I replaced all 3. Put machine back together, but washer still leaked. I ended up having to remove more components down along the center shaft towards the transmission. I found that the "tub seal" was worn out. I also replaced the "seal nut assembly" and "O-ring" while I was at it. The seal nut and tub seal were more difficult to remove without the proper tool, but a bigger rubber mallet and strategically placed pliers were enough to break them loose. Once all parts showed up the washer went back together easily and it is now leak-free.

This was easy except for the e-ring which was extremely difficult to remove. When I put the new one on I filed down the bottom of the front edges to make it easier to slide it on. Beware: If you have the washer tipped back against the wall when you do get the e-ring off everything will come sliding off the shaft all at once and go everywhere. These parts are covered with black grease and made quite a mess so you might want to have someone hold them in place so you can gently slide them off one piece at a time.

I found your site and looked at possible "symptoms" of the problem. Went to my washer propped it up with a 2 x 4 and manually spun the belt and sure enough the pulley on the drain pup was shot and grinding metal on metal. Ordered the new pump with pulley and a new belt (might as well change it when I had the thing in pieces).

1) Opened the front of the machine and then propped up the machine.

2) Placed a pan underneath to catch the water that remained in the pump when I disconnected the two hoses attached to it.

3) Removed old pump with socket wrench

4) Replaced with new pump purchsed from you all.

5) Reconnected the two hoses.

6) Installed new belt.

7) Closed up machine and BAMM! works like it was brand new!

You all Rock! Cost of parts and 20 or so minutes of my time is a lot less than calling a repairman or replacing the machine!

Thanks for the help!!!

I unplugged the electric power cord and disconnected the two water hoses and the drain line from the wall. It was messy as water leaked from the disconnected hoses. I tilted the washer forward and leaned it against a bench for support. This exposed the bottom of the washer from the back. I removed the v-belt from the three pulleys. The motor mount was spring loaded making it easy to remove the v-belt from this pulley first. After removing the v-belt, I then removed the 4 screws to the small plate on the back of the washer to gain access to the water pump. I then removed the two water hoses from the water pump using vice grips to squeeze the clamps and slide them off of the hoses toward the water pump. After removing the two hoses (a little messy again), I removed the water pump by using a socket ratchet to loosen the four bolts. I replaced the water pump with the new pump and then reassembled everything in reverse order.

I took out all the tubs and the apparatus holding the gear and thrust bearing assembly. I used a homemade tool (long zipties) to pull the springs off and to put them back on. After that I just replaced the thrust bearing with the new kit and put everything back together.

First I tipped the washing machine onto its front. I removed the belt on the bottom of the machine. Then I removed the screws that held the cover in place on the back of the machine. Next I removed the two hoses that were connected to the vertical pump using pliers to pinch the clamps. I then removed three screws that held the vertical pump in place. I took the new verticle pump with pulley and mounted it to the washer and putting the washer machine back together using the previous steps in reverse order.

I took the front pannel off just 2 scrwe was holdig the pannel,the motor was in ftont,4 bolt was holdig the moto,and it is very easy to change,

Overall, this repair should have been quite easy. The problem was removal of the old seal nut assembly. It was a bear to remove, and ultimately I had to surgically remove it from the washer in pieces. Unfortunately I broke the outer tub (plastic) in the process of getting the nut off. Once I had the silly plastic nut off, and the tub repaired the balance of the repair was absolutely easy.

My summary: This repair is really easy IF the plastic seal nut assembly comes off easily. If it doesn't budget easily, go ahead and chip it apart to get it off, being careful not to damage the threaded part of the agitator shaft. The new one will completely replace the chipped away nut.

The washing machine would shake very loudly when spinning.
Found red oil under machine. Asked experts, they said "buy new machine, not worth repairing transmission".
replaced small oil seal and drilled small hole and added some transmission oil(auto) then sealed hole. replaced belt just because the other one was oil soaked.
Works great, Like new, cheap fix under $20..

Placed the washer on 2 brick under the front. Removed the belt, used a straight blade screw driver for the lifting of the top off. reoved 2 bolts off the face and removed the screws of the water pump. Water pump was messy with smelly water but a bowel and a towel helps. Placed the pump on, reversed the tear apart...placed the belt on the bottom. Removed the brick under the front. Hooked up the water supply...plugged in and did a load..it worked perfectly....Thanks!!!!

There are two clips that hold the top of the washer down. Releasing these clips allows you to lift the top; it is hinged at the back. Then remove two screws holding the front panel and remove the front panel. The tub to pump hose is easily accessible. It is held in place by a hose clamp at each end. Use pliers to squeeze the clamps and remove the hose. Replace with new hose. I re-used the original clamps.

I felt extremely confident when purchasing the part because I say three diagrams which clearly showed I was ordering the correct part. 0. Drain all of the water out of the machine. 1. Remove the rear panel from the washer. 2. Use the pliers to disconnect the hoses from the pump. 3. Remove the three screwa from the old pump. 4. Support the washer with the block then take the belt off pulley. 5. Remove old pump. 6. put new pump in place then reconnect the pulley, you can remove the block.. 7. Install the three screws for the pump after you tighten it up by placing the pump over ther correct screw holes.. 8. Reconnect the two hoses using the clamps you removed. 9. Secure the rear panel and screw in place. 10. Wash clothes. EASY FIX!!!

Remover agitator/Auger assembly. Install new agitator/auger assembly. Washer still would not agitate. Called repairman and found the transmission was bad. Fortunately transmission was still under warranty. 10 year warranty on transmission.

I removed the rear panel of the washer, and removed the lid switch assembly. Then, replaced the old one with the new lid switch and plunger. Put the rear panel back on the washer, and started washing clothes again!!!!!! I think a monkey could have done it....