LAT2916ABE Maytag Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- justine from NEWARK, NJ
- Parts Used:
- WP6-2022030, WP213045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
pump and hose leak
Easily
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Starr from Mars Hill, ME
- Parts Used:
- WP22001274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
My cold water would not shut off
My husband took the old water inlet valve off, and put the new one on, and it works great. Very easy to replace.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from Friendswood, TX
- Parts Used:
- WP22001274
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Existing hot and cold water inlet valves leaking
First closed hot & cold water faucets feeding the two washer water hoses, then turned the machine on fill momentarily to bleed off water pressure in hoses, and unplugged power cord. Used pliers to help break seal on brass hose ends, removed old hoses. Removed 1/4 & 5/16 sheet metal screws, replaced leaky valves. New assembly was EATON Made in USA, high quality. Replaced rusted outlet hose spring clamp with "IDEAL" stainless screw clamp. Replaced unit in machine, installed new hoses, runs fine.
Was this instruction helpful to you?
Thank you for voting!
short in door lid switch
Unplug from electrical outlet.Unscrewed control panel and laid it open. The switch is in 2 parts. Removed wires and unscrewed each switch. Put wires back on and tightened switch back to mounting plate. No brainer. Tried washer and worked perfectly. Two tips: Check fuse on plate to make sure it isn't burned out before ordering any parts. Secondly when installing if you have older model washer there is a nib that sticks up on mounting plate that keeps the switch from installing correctly. Cut this nib off with a wire cutter and then install. The directions don't mention that.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- EL from O'Fallon, IL
- Parts Used:
- WP211726
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
Resin balls on which the top loader lid hinges had broken.
Cleaned the cavities. Lubed them with olive oil. Inserted one ball on left side, while holding tension against that side to hold the ball in the lid and top indentations. Applied olive oil to right hand side indentation, and placed the new ball into lid indentation. Put lid down into closure cavity with ball, and with lid vertical, began pushing it rearward so as toslightly spring metal lid rolled edge and top metal away from one another UNTIL the new ball snapped into the hinge indentation in the machine cover. Done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ronald from Madison, NJ
- Parts Used:
- WP213045
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer leaking at the front.
Our Maytag (A308) washer is now about 29 yrs old. I put in a PartSelect water valve 3 yrs ago. When it started leaking recently I found the cuplrit to be a flexible hose to the outer basis. The front came off easily (two screws at the bottom) and the hose clamps required some cleaning. I recommend purchasing new clamps. Under 30 minutes to get it running again.
Was this instruction helpful to you?
Thank you for voting!
Repairs Were Easy.
Removed top. Removed agitator and tubs . Replaced seals and reassembled.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- clayton from Kingman, AZ
- Parts Used:
- WP22001274
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
found water on floor checked it out found water mixer leaking.
shut off water to machine remove water mixer removed bracket. Installed new part put back together, turn on water, start washer all worked as it should.
Really like your parts selection.
clayton
Really like your parts selection.
clayton
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- nicholas from white plains, NY
- Parts Used:
- 12112425
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 15 - 30 mins
agitator did not move, all other functions OK
Removed the bottom belts to inspect. Belt for tub was well beyond it's service life. Belt for pump was OK. ordered the pair and replaced. When the washer was started the agitator still did not move. With power off I grabbed the agitator and pulled upward a few times then twisted it from side to side a few times. No change. Then I did the same with it with powered up ( a bit dangerous ). The agitator then ran OK.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Martha from Bryan, TX
- Parts Used:
- WP22001274, 22001190
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
Water was leaking down under machine from water inlet valve
I was really glad the parts took only two days to come in. My son did the work and very easy for him. I handed him the tools. Take inlet hoses off, go into back and top of machine to reconnect injector hose to tub. Then connect hose to intake valve replacing two clamps and connecting inlet valve to back of machine. Reconnect two water hoses to back of inlet valve and to the faucets.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Xuanbao from Norwalk, CA
- Parts Used:
- WP6-2008160
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
The washing machine ran noisily
Remove the power cord and water hoses. Lay the machine on the floor. Remove two belts (washing and pumping). Unlock the screw of pulley using a hex key. Remove the broken pulley from the motor. Place in the new pulley. Lock the screw of the pulley. Install two belts. Turn the machine vertically. Plug in water hoses and power cord. Level the machine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- jeff from shepherd, MI
- Parts Used:
- 12002351
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
motor went out
simply removed old motor and replaced with new
Was this instruction helpful to you?
Thank you for voting!
Not agitating ; top shaft seizing up
Removed tubs per prescribed videos. Removed transmission per video. Disassembled transmission per video. Used heat and penetrating oil to free top shaft. Lubricated top shaft and bushings with grease and reinstalled. Reassembled washer with replacement parts from partselect. Problem solved. My wife loves this washer. It lasted 30 years before I had issues, many of the internals looked brand new. They dont make' m like this anymore. With the self- help videos, and OEM parts from partselect, I'll get another 30, Thank you so much.
Was this instruction helpful to you?
Thank you for voting!
burning smell from washer
Replaced both the drive belt and pump belt in less than 10 minutes. Maytag has the easiest machines to work on.
Was this instruction helpful to you?
Thank you for voting!
pump and drive belt was thorn
Installed drive and pump belt.. very very simple. only tool required was a screw drive to remove front panel of the washing machine.
Was this instruction helpful to you?
Thank you for voting!