CAV2000AGW Magic Chef Washer - Instructions

I took the washer into the garage, removed access panel from back. Spun drive belt. This located the trouble with the pump. I removed pump with three sheet metal screws and hose clamps. Upon delivery, I notice the two pumps were not identicle. I called Cust Serv. They assured the difference was ok. I installed the new pump with three screw, put the belt and panel and hoses on and ran a test load of my junk clothing. No trouble.

I used a needle nose pliers to release the turning mechanism from the piece left broken on the timer. Once removed, I simply clicked on the replacemnet part. It was super simple. I love that I can do most things myself with the parts, and not have to pay the expense of hiring a repairman.

Studing the numerous notes under the parts listing, help me determine which parts to purchase and replace. These listings also helped me to do the repair with much ease. Once the front and rear panels were removed, I detached the springs which came out very easily. I then pulled out the tub and removed the pulley and loosened the screws holding the snubber which then came out. Put in new snubber tightened screws, replaced pulley & put tub back in place. The springs were a little tougher which led me to believe the old ones were streched. I used a towel to brace tub to one side so as to attach spring on the low side. Used Vice Grip pliers and could not phathom using anything but. Put everything back together and washed a load of towels. The tub was way more stable, but still, towels were little damp. Respun and they dried. Determined that the repairs was all good but told wife not to put so many towels in at once which is probably why the snubber & springs wore out.

disconected water lines unplug power and took drain pipe off, used putty knife to open top of washer and pulled off front removed pannel off back pannel, disconnected water level tube,using vise grips took off springs and pulled tb out used 5/16 socket to loosen screws just enough to pull snubber ring out replaced with new one reversed prosses in putting it back to geather

Actually I got on YouTube and looked up the problem and watch the short video of it and went from there and it showed me how to take everything apart what the problems were and as I did take it apart and found out it was exactly what they said I simply reversed it just ordered the parts and put them in and took my time to make sure that everything was to specs as I've measured the clearance of the break and said all the hardware back in place it was quite simple yet it was just time consuming took me about two and a half hours but it runs quiet spins great just like a brand new one I couldn't be more pleased with it and I saved quite a bit of money doing it myself

followed video instructions

Hving read some of the tips in regards to this repair I set out with equal parts of confidence & apprehension. The advice of shifting the tub toward the hinge to be removed is in itself the key to the whole procedure. After having done so & wedging a dust pan handle between the tub & frame to first one side & then the other, I removed the entire lid with the hinge & hinge pin assys. attached as ther is not sufficient clearance to slide a servicable hinge pin from a hinge when only one hinge has beeen removed. With the lid completely removed access to the hinge pin(s) is straight forward. I suggest screwing & unscrewing the fastening screw into a new hinge assy before mounting the hinge onto the machine & also using an offset philips screwdriver or ,as I did, a 1/4" drv. ratchet with a #2 philips apex bit which allows for a better feel & more control over the upside down blind operation of removing & replacing the fastening screw into the hinge assy. Hope this helps. Tom

On a scale of 1 to 5 (with 5 being the most difficult), I would rate this a 2 or 3. It is just a matter of knowing how to access the pump. First I unplugged the washer. Then used putty knife to push in clips to lift up top of washer (the clips are located about 1 inch in from each side). Used socket to remove the two screws holding on front panel. Disconnected the two hoses from pump using pliers to squeeze clips (be sure to have cup or bowl handy because water will come out of the hoses). Lifted up washer and removed belt from pump. Used socket wrench to remove pump and replace with new one. Reattached hoses and belt. Reattached front panel and closed the top of the washer. Everything was easy to access.

First i unscrewed the bottom latch to check inside the maching, i then disconected the vertical style pump with pulley from its position and i discoverd a huge crack that was made by a loose pulley. After that i ordered another pulley from this web site easaly installed the pulley and now my maching works like new. The part was less than 50 bucks i saved over 200 bucks by not going out and buying a new machine.

I first had to take the old part out to find out what the part number was. Then I went online and ordered the part. Once the part came in I attached to part and replaced the drive belt. I did not think it could be so easy.

Removed one bolt, main thing was I had to buy a 10 inch extension for the socket and wrench to reach inside of the agitator, pulled the old one off replaced the new one tighten the bolt and I was done. 10 minutes start to finish.

The hardest part was finding the model # on the back. I couldn't move the washer out...so used a mirror! I used a putty knife to pop the 2 fasteners securing the top. Tilted it up & proped with a plastic clothes hanger. Unscrewed the one screw which is easy to get to with the top up. Replaced the hinge with the 1 screw. Closed the top. Gave the broken hinge to my wife as an early Mother's Day present.

unscrewed screw holding old actuater in and replaced it whith the new part.

First I lifted the top of the washer to get access to the screws that held the hinges in place, unscrewed them, removed the broken hinges and put the new ones on, replaced the screws and closed the top. It was very easy. I was amazed that I could still get replacement parts and at such a great price, less than $15.00 with shipping!

Pretty simple repair--popped the fabric softener cup off of the agitator top and took out the bolt that secures it to the assembly. Removed the broken agitator top, replaced with the new one and reinstalled the bolt and softener cup. EZ as pie for only $24 including shipping! Great price!

Fabulous turnaround time from www.partselect.com. I had the problem corrected inside of 4 days using standard shipping. I will definitely do business with them again!