W205KAC Magic Chef Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- steve from WATSON, MN
- Parts Used:
- WP21001915
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Tub to pump hose worn out and leaking
Replaced the hose. two clamps and retainers. very basic repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from Palmdale, CA
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers
Water removal pump stopped working.
Removed lower rear panel by removing 8 screws. Then I removed the two hoses that are attached to the pump by removing the hose clamps with a pair of plyers. The three hex head screws that anchor the pump to the base of the washer unit were removed and the pump came right out. To put the new pump in I just slipped the pump through the hole at the bottom of the washer and attached the belt onto the pulley. Then reversed the installation process. The washer had to be tipped forward slightly for this process and blocked (approx. 8 in.) to allow access to pulley. Very easy install, no help needed. Washer must be empty and preferable dry when task is done or water will be everywhere.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- marilisa from naples, FL
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Socket set
loud grinding sound then washer would shut down then there was water all over
first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joe from Clearfield, PA
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Water leak
Removed front cover, identified leak, ordered part, saved over half of the cost on part, no service call fee. I feel great!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Wabash, IN
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
washing machine squeaked on the spin cycle
removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- felicia from Broken Arrow, OK
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
The water pump went out
UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel that you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert E from Katy, TX
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Whasher would not drain
Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BILL from DIX, IL
- Parts Used:
- WP35-6465
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
The Pump Went Out & Water Was All Over My Floor..
Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffrey from Flat Rock, MI
- Parts Used:
- WP21352320, WP21001108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Broken Belt and Motor Pulley
Repair was very easy. I removed the old pulley from the motor shaft by breaking it. And then tapped the new one into place. It works great. DON'T buy a new motor for $120, just replace the pulley $6. This whirlpool pulley fits the Admiral motor perfectly!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jimmy from MEMPHIS, TN
- Parts Used:
- WP89503
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers
Old hot water inlet hose had budge at both ends.
Turn water off at the inlet valve of hose you are replacing. Disconnect inlet hose the washer and let water drain out in a bucket. Then remove old hose. Replace new hose to inlet valve then washer . Use pliers to tighten both ends. Turn on water to check leaks at both ends of hose.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- FRANK from CHULA VISTA, CA
- Parts Used:
- WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
water not draining
changed drive belt and saved me from buying new washer,,working like bland new again ...many thanks
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jose from Elizabeth, NJ
- Parts Used:
- WP35-6465, WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Made noise during washing and rinse cycle
It was easy to replace the water pump
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michele from Lebanon, PA
- Parts Used:
- WP35-6465
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers, Socket set
Started making loud screeching noise(bad Bearing)
Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Russell from LOS MOLINOS, CA
- Parts Used:
- WP21001108
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Wrench (Adjustable)
pulley got hot and broke
replaced pulley and belt. Looked for a pulley for 1 week at retail stores. Found pulley on parts select
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Les from Moneta, VA
- Parts Used:
- WP35-6465, WP21352320
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Made noise on spin cycle
Took off belt and ran motor. No noise. Then took off drain pump and spun it by hand and felt rubbing on one spot. I figured the bearings were going bad, so I ordered the parts and replaced them.
Was this instruction helpful to you?
Thank you for voting!