CAV2070LKW Magic Chef Washer - Instructions

I had my boyfriend take the lid off ,then he took off the two old hinges,one was broken,and the he replaced both lid hinges,daving the good one. it was very simple and quick for him.

Iwill use your service again,thanks.
Loyce Floyd

Removed water lines and drain, removed back panel, removed drain lines from pump. Unscrewed 3 screws to remove pump. attached drain lines to new pump, screwed in new pump, reattached everything. Reinstalled belt (very easy, not like an altenator). done

removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!

UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel that you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.

Used a water hose to syfen out the water. Placed hose in the tub. Turned outside facet to fill hose. Undid hose outside and allowed to drain. Pulled pump. Order online ( Delv fast 2 days ) .Replaced pump . Works great . Good luck with yours.

short drive, 90 degree, "star" driver. push tub to side and back to reach lower part of old hinge, remove single screw. (careful not to drop it into the "mechanics" of the tub.) repeat for the other side. remove parts from lid. reassemble new parts onto lid, along with lower hinge parts. secure the lower hinge to door part(s) with masking tape to hold in place. hold lid in place over lower hinge screw holes and start screws by hand. snug up the screws and your done! the 'STAR" screws may be relpaced with similar "phillips" so you wont have to scrounge for a "star" driver the next time.

I followed the feed back in the forum from a previous repair. I popped open the top of the Washing and propped it open @ approx. 70 degrees,moved the Tub out of the way and used a small Phillips Scwdrvr to remove the broken part, installing the new parts was a snap, I took the time to use a Q-Tip and petroleum jelly to coat the pin and hinge making it easier and less binding when opening the lid.

Went to website, looked up make and model, looked at photo's discription, studied it, and then went in and removed front panel, turned off water, removed clamps holding hoses too dishcharge pump, mopped up water, and then just reinstalled new piece, the way the old came out, re attached belt to pulley assembly, turned water back on, and did a test for leakage and wala washer back in working order in less than an hour, and saved hundreds of dollars with out maytag repair man.

Reverse the process to install new pump
Unplug the machine
Place pad on floor to protect the machine from scratches
Lay front of machine on floor
Remove back cover (10 screws)
Disconnect 2 hoses
Remove 4 screws which secure pump to bottom frame
Remove belt
Remove pump

Reverse the process to install a new pump

Your web sites intuitive design makes it easy to navigate and the customer service person was knowledgeable, easy to understand and professional.

The part arrived via UPS in 3 days. It was double boxed (well packaged) and most importantly, it was the correct part.

This was is 1st time we used your server but it won’t be the last!

Kudos to the entire staff and please…keep up the good work.

Sincerely,

Lon Thomas

Unscrewed the front panel. Then took pump out & put new one in. . . . . Thank you part select. Com. . . Super fast shipping. . .

Opened hinges top of washer. Removed screws holding hinge bases. Removed the washer top lid and unscrewd broken hinge pin. Replaced hinge pin and inserted in pin base and screwd base op hinge back onto washer and job was done.

I followed Gary from Sioux City IA instructions. Very well explained.

I followed the instructions that other posters suggested. The springs were the toughest part to remove and reinstall. Having my wife push the tub enabled me to use vice grips to get them back on. Read about the coins or washers to spread the springs too late... would have helped. Running a wash now and it's spinning great and no noise!

Turned water off,tilted unit forward,removed lower rear cover,removed belt,laid towels around ,removed inlet hose and exit hose off pump,removed 3 screws holding pump,removed pump and installed new one,reversed order of disassemble, has been running great ever since.

I unscrewed the old lid switch and screwed on the new switch in seriously 2 minutes!