CAV2000AWA Magic Chef Washer - Instructions

Brought unit out to garage so I would have room to work on it. Popped the top off, removed two screws to remove the front panel, removed back panel also, since there was no way I was going to the trouble of dis-assembly to get to the snubber without changing those 6 springs also - and you HAVE to remove the back cover to access all 6 springs.Removed belt and level and drain hoses- tub came right out. Loosened those 6 screws without removing them and pulled old snubber out- very straight-forward. Spent 10 minutes just comparing the old and new snubbers- I saw that there's a "ridge" around the inside of the new part that is gone on the old snubber. Sprinkled some corn starch at base of unit where the new snubber will fit (Great Idea someone had!) After everything was re-assmbled, I noticed the tub was now nice and tight when I grabbed it to move it. Before, it took no effort AT ALL to move it all around. Did a test load with some laundry the wife had stacked on the drier. Imagine my disappointment when I heard loud knocking inside when it started to agitate, but not while it spun!
Got all my tools back out and took the wet laundry out to take it all apart again- found the wife's heavy glass vase had been hidden in one of the towels. Re-tested- everything works GREAT!So far I've changed the drum seal (hardest) and the waterpump (easiest)- thi springs and snubber was alsmost as easy as the pump.
Above average shipping from Parts Select also- very helpful and efficient people on the phones.

Unplug power cord; turn off hot and cold water supply; remove water hoses from machine; open top of machine by prying lid open; remove two hex screws holding water inlet valve in place; remove hose from top of old water inlet valve; remove 4 wires; connect bottom set of wires (red and white) to new water inlet valve; reinstall water hose to top of new water inlet valve; install new water inlet valve onto machine using same hex screws; connect remiaining red and white wires; install hot and cold water hoses to machine; turn on water supply valves at wall; reconnect wall plug; turn water type selector to cold, pull out timer and watched the water flow full-force for the first time in 2 years! Have wife give you a hug for saving cost of new washing machine!

Removed the inner basket and outer tub to replace the gasket and rubber seal. just had to remove about a dozen screws to get it out.

Tipped the machine up to replace the belt.
The noise didn't go away at first. I decided to spray all the pulleys with some silicone spray, that did the trick.

As described in video; however, the video does not match the model I repaired. Most stuff is the same. Hardest thing to do was installing the new springs on the back of the tub (2 of them).

Pop the top of the washer and use the nutdriver to remove the two screws holding the frontpanel on. Use the nutdriver for two more screws holding the plastic motor cover on. Use nutdriver for the two BIG screws holding the motorplate to the washer frame. After this, I literally beat/chiped/sawed the old motor geat off. Once that was done, I put the new one on; had to use a hammer to knock it all the way on (try not to damage the clips). Reassemble everything. Flip washer over and place bet around two smaller gears. Rotate main tub gear to feed belt on. Make sure you use the nutdriver to loosen/tighten the motor positioner screws in the slots if things aren't working here.
The only really hard thing was taking the old motor gear off.

remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three screws back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.

Took off the back plate. Looked to see where it was leaking. Squeezed the clamps on top and bottom to remove from hose and pull hose out.

Removed the front panel to get some light in to the machine. Removed the two hoses connecting the pump to the drain and tub. Removed the three screws holding the old pump in place. Did the reverse to install.
This was a piece of cake.
Thanks for having the parts needed to do this job.
Tom

Replacing the pump with the new pump was very easy for me, because of my degree in Mechanical engineering, so I am use to dealing with pumps, engines, gears,etc. However, my wife watched me do the entire job and she is now able to replace this part in the future. The design of the Maytag is very simple to repair, and for that I am very greatful that we can order the parts and do the repairs ourselves withhout having to call a repairman. This was our first problem after 6 years of smooth operations by this washer.

I took out the agitator first, then I took out the inner tub, next I took out the outer tub, and last I took out the transmission assembly. After replacing the snubber I put the transmission assembly back on, then the new outer tub and next the inner tub. Last I put the agitator back on.

I removed the screws and the power connection to the timer. I had to remove the broken plastic piece stuck in the collar with pliers.
I as able to get it put back on and working pretty quickly. It is too hard to describe it all here but I got it fixed and saved about 120.00 doing it myself.

first removed panel from rear of washer removed hoses and drained water in them, removed the 3 screws and removed the belt then removed the pump. Replaced with new one and put back screws,hoses and belt. walaaa.... it works like new!!!!

used putty knife to to raise the top, took out two screws, replaced parts , then closed the top.

Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconnected the power and water hoses and everything worked fine.

Changing the hinge was not difficult, but here's a hint: the top of the washer raises up if you pry it with a big screwdriver- be sure to wrap the screwdriver in a cloth so as not to scratch the appliance. Doing it this way makes it easy to access the retaining screws. You can push the wash tub to one side and reach the screws from underneath, but they're a tight fit and doing it that way is difficult. Overall a pretty easy repair and I'm only moderately handy.