W20JA4 Magic Chef Washer - Instructions

Unplugged everything, disconnected hoses, took belt off and put new one on.

Spoke with a trusted repair man, described the problem best as I could. I smelled a burning rubber smell. Got on Internet for troubleshooting problems, 77% likely a drive belt. BINGO! Ordered a new belt, took old one off, cleaned the pulley ( it had burnt rubber stuck on it, difficult to remove) lightly sanded pulley just so it would be really smooth. replaced belt. Magic, it worked. I am no repair woman, but carefully listening and explaining helped. Oh, belt is under the very bottom of machine. Very easy to get to, just tilt back and lodge at an angle and make sure it doesn't move.

I first opoen the front panel of the washer. That was a bit tricky. Had to slide a thin blade between the top of the washer and the front panel, pushed in to release the "clamp" and gently raise the top, it hinges on the back.
The rest was undoing three bolts, refit the new pump and put the belt back on.
The part cost me less then $65.00.
The repair estimate by the local repair man was $ 250.00.
I am very happy.

Thank you PartSelect.

Andre M. Roberty

Removed back plate, tilted up washer removed pump removed belt. Then replace pump and then replaced belt

I ordered the replacement pump assembly (water pump)for my Atlantis model maytag washer, removed the old one, installed the new one and works like a charm. The only difficulty I had was trying to figure out how to remove the cover on the front of the washer, to remove the clips, it slid side to side instead of popping out, found the instructions on-line, NO instructions came with the pump but if you have any common sense when it comes to repairs it was easy to remove and install the new part.

Unplugged electrical plug. Disconnected water and drain hoses. Turned washer on front side. Removed old belt from bottom of washer. Removed pump access panel. Removed old pump. Installed new pump. Torqued pump mounting screws 1/4 turn with socket wrench. Installed new belt. Put on pump access panel. Hand tested motion of belt and pulleys for smooth travel. Put drain hose on. Turned washer in the upright position. Reconnected water hoses. Washer works like new.

took off back small metal panel, tilted washer front side down, easy to put into place after removing old part

Because I live alone, the washer is very heavy so I just used some sliding robots under the legs of washer so I could slide it out from the wall by myslef after removing the small plate in the back to accfess the water pump I used the nut driver to remove the 3 screws holding the pump in place, but I used the pliers to remove the 2 water hoses first then I mounted the water pump back into place, installed both hoses again then I tilted it back against the wall while re installing the belt then I pushed it back against the wall and removed the sliders so I could make sure it was back level this was a very easy repair even if you never fixed any thing before the belt replacement was even more simple to replace because the motor is springloaded so you just had to pull on it enough to remove it from the pulleys

took drum out replase snubber put drum back in

1- Unplug unit 2-disconnect water hoses 3-put unit in open area so you can work on it. 4-Open top cover with screw driver 5-take off front cover with appropriate socket 6-lay unit on it back to get access to the drive belt (take off). And take off water hose with plyers. 7-With vise grips take off the six springs. 8-Take tub assy out,and lay it on the floor upside down. 9-Loosen the screws to take out the old snubber ring, note ( when lossening screws,keep your finger on the bottom of the screw ,so you can feel how far to back the screws out,just enough to have access to the snubber ring,to take out,and install new one. )Remember not to take screws out completely. The unit is under spring tension. 10-Put washer back together in reverse order,and problem solved!

Had wife balance washer on front edge while I accessed working parts from bottom of washer. Removed drive belt and turned agitator pulley, transmission pulley and drain pump pulley by hand. Drain pulley hard to turn and shaft had play in it. Ordered new drain pump and replaced upon receipt. Very few fasteners to remove and replace pump assembly. Drive belt was easy to remove and replace. Recommend also replacing drive belt on a washer this old.

Turned it over to my 35-year old son who removed pump and pulley assembly and the old drive belt, then simply replaced with new assembly and belt from PartSelect! Could not have been easier - from my viewpoint.

The Clamps for the hoses were difficult to get to, otherwise was a simple replacement job, involving clamps and screws and bolts.

I had to raise the top of the washer and take off the front pannel. It was not too hard to replace the pump except that it was in the back corner and it was hard to reach the bolts to remove and install the new pump.

Raised washer. Identified problem. Removed from panel, gaining access to drain pump. Removed hoses, replaced pump. NOTE: I used blue Loctite on pump mounting bolts. Reinstalled from panel, lowered washer, cleaned drum. Ran one (1) cycle with hot water and bleach ONLY.