W26HA5K Magic Chef Washer - Instructions

remmoved the screws on the back that hold the panel on. removed the two hoses attched to the pump. removed three screws and pulled the pump out. spun the pulley and noticed no movement inside. looked closer at the pulley to notice it was broken. ordered new pulley online. received quickly. new part fit exacttly right. put three screws back in. hooked two hoses back up. put belt on pulley. plugged in and worked great.

removed hoses and belt. removed 3 screws that secured pump. and then removed pump. received new pump and just reversed the process to repair!

UNPLUG ELECTRICITY. I pulled out the washing machine turned the water off pulled all of your hoses from the back of the machine there may be a mess so you need some thing that will catch the water as it comes out of the hoses. On the bottom of the machine is a belt you have to remove it. Its easy just pull it off. On the back is a panel that you unscrew four screws. On the water pump it self you unscrew three screws. Then for the new part you do in reverse order screw your three screws back in put your hoses back on make sure your clamps are tight around your hoses or you will have a leak. Put your panel back on. Put your belt back on. Turn your water on from the wall plug in the electricity and you are done.

Disconnected both power and hot and cold input water lines. Laid the washer on its front side for access to the bottom. Removed the small access panel from the back of the machine to remove the metal screws holding the pump in place. Removed the single drive belt. New pump installed easily, replaced the belt and access panel. Reconnected the power and water hoses and everything worked fine.

I removed the cover on the back of the machine, detatched the 2 hoses and removed the 3 screws holding in the Vertical Style Pump - with pulley. These screws are 10 mm nut-driver. The cover if I remember correctly was a standard rather than metric so make sure you have both available.

Screwed new part in, re-attached hoses and replaced cover. The last step requires strength to hold the machine up and re-configure the belt. This is best accomplished by looping it onto the tub and the pump first, the using the tub pulley to maneuver the belt onto the motor.

Only discouragement was that it took 8 days to receive the part as the first shipment was not the correct part at the fault of the distrutor.

first i removed the front panel unclamped the hoses unscrewed the 3 screws that hold it in pulled it out, opened the new one and actually dropped it in and it fell into place with the holes lining up inserted the screws and hose clamps and reinstalled the belt which fell off when the old pump was removed, put the front back on and gave it a test then let the wife do a load of wash it worked like new

after doing some research I found out that a loose or slipping water pump belt could cause the water pump to not pump out the water correctly. Under the washer is the belt. All you do is have someone lift the front of the washer up enough that you can reach under and remove the belt. Then replace the belt back like you took it off.

pulled the machine out, tilted it backward to expose the bottom. pulled off the old belt. got the new belt started on the three pulleys. pulled the belt to spin it , and...............done !!

Piece of cake. Raise up the front of the machine. the belt slips of easy by turning the main drive wheel. put the belt on the two small one and then rotate the big wheel as you slip the belt into the grove. good idea to first clean the wheels of any old belt material that may be worn off. Piece of cake!

Replacing a belt on a washing machine is a pretty easy process, depending slightly on how easy it is to access the belt. On our Maytag, the belt can be accessed directly underneith the washing machine. So, I lifted the front of the machine and put a few blocks of scrap wood under the legs to hold up the front of the machine. Once that was done, there was nothing else that needed to be removed to access the pullies that the belt had to go around. The motor itself is generally adjustable to allow the belt to be changed. So, I first wrapped the belt around the largest one that spins the washin machine tub, and then wrapped it around the one that spins the water pump. Finally, I loosened the bolt on the motor to allow it to move, wrapped the belt around the motor, pulled the motor back to tighten up the belt, and tightened the bolt that holds the motor in place. It's a pretty straight forward repair that narly anyone could do thmselves.

Removed access panel to expose pump, removed drive belt, and old pump, repeated the avove steps in reverse order, tested for leaks and proper operation.

First , I unlocked top cover and propped; removed front cover. tilted machine back propping front. pump is at lower right corner, removed both hoses, removed belt and three screws. reversed order completing job. You will have some water leakage removing hoses.

Disconnect all water supply and unplug washer. Remove 3 screws on back panel of the washer. This will expose the pump unit. Detach belt on the bottom of the washer. Then detach two hoses that connects to the pump unit. Use pliers if necessary to disconnect hoses. Use 5/16 socket with extension to take out three bolts the connect pump to the washer. That's it, now replace old pump unit and with new. Place bolts back in the 3 holes, reattached hoses, cover the back with 3 scres. Connect the belt to the pulley system on the bottom. Connect water supply and plug it in.

Pulled that sucker out from the wall and leaned him back just enough to prop a case a beer under it. Slid up under there with the biggest dust bunny I ever seen. Yanked that old belt off and threw it away. Tried to uncoil the new one and it slapped me in the nose! Got it uncoiled and around the two smaller pulleys pulling the adjustable one in to it's limit and walked the belt around the big drum pulley. By the time my wife put down her coffee and came to see if she can lend me a hand I was done!.

It took long because I did not know where the noise is coming from and I took the sides off. I went to the store and bought a new washing machine. Delivery was scheduled in 3 days. I decided to lay the machine on its side and look underneath. I pulled the belt off the 3 pulleys and turned each pulley by hand. The one runing the pump was stiff and noisey. I ordered the part, arrived in 2 days, installed it in 15 minutes and closed the machine in 30 minutes, then cancelled the order of the new machine and saved $500.00