40318 LG Washer - Instructions

E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.

-Unplug washer
-Turn off water supply
-Pull machine away from wall
-Remove two screws on the back holding the top panel in place
-Slide top panel toward the back and remove
-Unplug electrical conectors to the control panel, remove screws and take out panel.
-Remove lint trap plastic door cover bottom front left and screw holding plastic housing.
-Take housing out.
-Remove screw that is behind plastic panel holding front panel.
-Using spanner, release spring clamp holding gasket to the front panel.
-Remove top screws holding front panel on and take off panel.
-Remove hose clamp and hose at bottom of gasket.
-Release inner spring clamp on gasket to washer drum and take out gasket.
-Install new gasket and spring clap to drum.
-Reverse the order to reassemble.

Disassembled washer, replaced bearings, seals and gasket. Watched instructional video to familiarize myself with the repair. Followed all steps as recommended, repair was straight forward without any surprises. Hardest part was removing the drum from the machine, somewhat heavy. Disassembled and replaced all bearings, seals, spider and gasket. Reinstalled in reverse order. Note: Upon tear down, I found the seal was pushed out, causing the bearing failure. I also found that the seal was installed incorrectly from LG. They have the seal lip facing the bearings, should be facing the water. This repair seems to be difficult, but was fairly self explanatory. All plug ins are color coded, all hoses are accessible with little effort. If you have basic skills you should be able to handle this repair.

Super straightforward to diagnose and repair.

There was puddle under the washer.

I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.

Two hose clamps to remove and replace, then replace the top and ready to go.

2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.

removed top and front. heater is at the base of the tub. the nut compresses the rubber seal and may take some wiggling to remove the old one.

It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

After watching the video for installation of the bellow, I followed the suggested repair method and was able to repair my washer.

just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here

I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).

I tipped the right side of the washer up 9.5 inches using two 2x4s and I was able to remove and replace the old hose with the tools described.

When to utube typed in my problem, very easy fix

I removed the tub. Thin included disassembling the washer and disconnecting various hoses electrical connectors to facilitate the removal of the tub from the machine.
Once removed, I separated the two halves of the tub and removed the metal basket to gain access to the bearings and seal.
Removal of the bearings was much harder than expected as they were very difficult to drive out of their pressed in mounting.
I finally was able to remove the bearings and fabricated a press using a piece of all thread and two steel plates to install the new bearings and seal.
I would not attempt to do this again with the proper bearing pullers and an official press to install the bearings gently without beating the tub housing.
This repair I feel is beyond the scope of your average DIY. The bearings can be damaged easily without the specialized tools to install the components.

Entire machine must come apart to replace part. You tube installation instructions. They said at least a 3-4 hour job. Took me 4. I could see this repair costing at least 800.00 Would be worth buying a new machine but doing it yourself cost 225.00 and your labor