F1403RD LG Washer - Instructions

ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!

Unscrewed 2 screws holding part. Removed old part & replaced with new.

replaced switch as shown in the video...Worked great

After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.

Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires

To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.

Watched the easy video instructions on the product page and did the same on our machine - pop off the top, unscrew the plate from the front of the door inset. Its a little challenging to unplug the old lock assembly because it is a tight fit and not enough room for two hands to fit to provide a bit more leverage when pulling the power lines out, but once its out it is easy to install the new one and reattach the strike plate frame and top of the washer. Plugged back in and we were back in business. This $50 part ended up saving us at least $300 in repair fees to get it working again.

Incredibly fast shipping - arrived in less than 2 days - which was really helpful as we were unable to use the washing machine until we were able to get this fixed. Excellent pricing as well. Couldn't be happier I found this site and the product I needed so easily.

Followed instruction from you tube. Removed gasket holder, then gasket by door switch assembly then replaced with new assembly!
I am a 63 woman and found this easy to do, with help from you tube guy.

It was easy to remove the rubber gasket to get at the door lock. Removing the door lock and replacing was simple enough, but getting the metal ring securing the gasket was cumbersome and challenging. This took most of the time.
However, after replacing the door lock it was obvious that this was not the problem. I had to remove the new part and replace the old one.
For future, it was the pob circuit board that was defective and had to replace it. Apparently this is not an uncommon problem as there are a number of UTube videos about this.This job was more involved and took me over an hour and resolved the issue.

When to utube typed in my problem, very easy fix

Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

Turn off hot water supply and activate a cycle on the washer momentarily, with hot water selected on front panel options to relieve hose pressure. Slide washer out to gain access to rear of unit. Unplug washer from AC source. Using pliers, remove washer supply hose from washer-side of the line (water may drain from hose) Remove single Phillips screw at bottom of each nylon lid holder at rear. Using a plastic putty knife, place between front panel and top lid to loosen lid and slide to rear. Remove lid and store aside. Hot and cold inlet valves sit side-by-side at top rear of the unit. Disconnect connector from valve by pulling gently away from valve plug prongs and place to the side. Using pliers, compress hose clamp and move to lower section of hose. Carefully rotate hose back and forth to remove from assembly. Inlet valve is held to washer body rear with 3 small Phillips screws. Remove first 2 and then while holding inlet valve body, remove final screw to free inlet valve assembly. Replace with new assembly by reversing these steps.Make certain when supply hose is reconnected, it is firmly tightened but DO NOT over tighten. Test washer by running a cycle to ensure there are no leaks.

Unplug washer!!! 1. Remove retaining ring around rubber gasket with flat head screwdriver. Just slightly pry off and it will easily come off. 2. Just peel back rubber gasket on the side that the lock is on. 3. remove 2 screws from the front off the lock assembly. 4. gently reach in and lift the little plastic clip holding the wiring harness and lift straight off. If the clip is lifted it might be a little tight just use even steady pressure to pull off. 5. Reverse these instructions to replace. Note: replacing the retaining ring on the rubber is a pain. The spring has to be in the bottom. Using a couple of flathead screwdrivers you can wrangle it back in place after awhile. There is a tool that looks like a large reverse pliers that may make it easier. Anyway thats it, pretty easy. There is a youtube video that shows all of this.