WM LG Washer - Instructions

Remove where the water pumps are and remove the one that was damaged easily

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

I followed instructions, posted by this site ln so doing, I saved at least $ 800. Dll`s

I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars

I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.

When to utube typed in my problem, very easy fix

The repair went good but time consuming. I replaced both inner and outer tub bearings along with the tub seal. I removed top by removing two screws in back then pulling back slighty then lifting up. I removed soap tray by pressing down tab and pulling out. Loosened soap dispenser and folded back on top. I removed control panel then front door panel. Remove back panel. Remove motor and shocks and hanging springs which there are two. Disconnect the hoses attached to tub then pull the tub. Remove screws holding the tub halves together. Use punch to remove bearings. NOTE: If you put the bearings in the freezer prior to installing, they go in much easier. I used the old bearing, set it on the new bearing then I tapped the old bearing so not to damage new bearings. I replaced the seal then put everything back together. Not difficult but time consuming.

Followed the video supplied by this site and everything was as described!

I removed the tub. Thin included disassembling the washer and disconnecting various hoses electrical connectors to facilitate the removal of the tub from the machine.
Once removed, I separated the two halves of the tub and removed the metal basket to gain access to the bearings and seal.
Removal of the bearings was much harder than expected as they were very difficult to drive out of their pressed in mounting.
I finally was able to remove the bearings and fabricated a press using a piece of all thread and two steel plates to install the new bearings and seal.
I would not attempt to do this again with the proper bearing pullers and an official press to install the bearings gently without beating the tub housing.
This repair I feel is beyond the scope of your average DIY. The bearings can be damaged easily without the specialized tools to install the components.

I watched the you tube videos to figure out where everything was. It is a really good idea to mark carefully which pipe goes where to avoid screw ups on re-assembly
The only slightly difficult thing was to locate the catches on the lower edge of the front of the washer top and press them in with the putty knife to release the top of the washer (They are approx 2" in from either side on the front of the washer on my model)
I chose to replace both the hot and cold assemblies - I figured it was the cold which had failed (the more expensive one) but as I had it apart it made sense to do them both.
It fixed the problem. Been two months now - There have been no repeat floods - its all good!
Shipment of parts was fast, and parts were correct for the washer.
I estimate it saved me at least $200 in technician fees by doing it myself. Thanks guys!

It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.

Followed instruction from you tube. Removed gasket holder, then gasket by door switch assembly then replaced with new assembly!
I am a 63 woman and found this easy to do, with help from you tube guy.

After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.

To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.

It was easy to remove the rubber gasket to get at the door lock. Removing the door lock and replacing was simple enough, but getting the metal ring securing the gasket was cumbersome and challenging. This took most of the time.
However, after replacing the door lock it was obvious that this was not the problem. I had to remove the new part and replace the old one.
For future, it was the pob circuit board that was defective and had to replace it. Apparently this is not an uncommon problem as there are a number of UTube videos about this.This job was more involved and took me over an hour and resolved the issue.