WM3550HVCA (ASSEEUS) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- lawrence from DOBBS FERRY, NY
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Water wouldn't drain
I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria D. from MEMPHIS, TN
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken retainer
pops right into hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- paul from DELAND, FL
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
door lock malfunction
ridiculously easy. removed the door gasket ring clamp. separated the gasket from the face. unscrewed the lock, removed the wire(gently). replaced the wire on the new lock. replaced the lock. replaced door gasket and ring clamp. washed clothes. Note- I had called a repair service and was given a $360 estimate in addition to the $130 dollar service charge. All total- $50 dollar part(with shipping), less than 45 min total time and I'm no mechanic!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Charles from EATON, CO
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Door Lock Switch Replacement
The video from PartSelect showed removing the retaining ring from the rubber washer tub boot to then allow access the door lock located behind the boot for replacement. That ring can sometimes be a real pain to put back on. This can be avoided altogether!
It's much easier to access the door lock switch by removing the two retaining screws on the top cover of the washer found in the back of the machine. Remove the top cover and you can then reach down to remove the wiring connector, unscrew the two phillips screws on the front of the door latch and remove the door lock. Put the new switch on in reverse order; plug in the connector, replace all screws and the top cover, and you are done! This method took than 10 minutes from start to finish.
Please note that the washer should be unplugged from power while working on any electrical component.
It's much easier to access the door lock switch by removing the two retaining screws on the top cover of the washer found in the back of the machine. Remove the top cover and you can then reach down to remove the wiring connector, unscrew the two phillips screws on the front of the door latch and remove the door lock. Put the new switch on in reverse order; plug in the connector, replace all screws and the top cover, and you are done! This method took than 10 minutes from start to finish.
Please note that the washer should be unplugged from power while working on any electrical component.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lois from ARIZONA CITY, AZ
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
the magnetic door plunger fell on the floor,
the magnetic door plunger fell on the floor, would not stay in place and did not hold the door closed. Received a new on, put it in place. works just like it is supposed to. took all of 2 seconds. great service from
Partselect. got the new part in less than a week.
Thank you
Partselect. got the new part in less than a week.
Thank you
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from WASHINGTON, DC
- Parts Used:
- 5220FR2008F, 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Water continued to flow into machine during drying cycle and afterwards
This was a very easy repair. Just followed the steps in the videos on the website (I replaced both the hot and cold inlet valves, so two different videos, but the process for each is similar) and it couldn't have been simpler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from PITTSBURGH, PA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Drain pump inoperable
1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- BRAD from AUBURN, MA
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
WASHER WOULD NOT FUNCTION BECAUSE DOOR LOCK ACTUATOR (ORIGINAL) FAILED.
WATCHED VIDEO PROVIDED BY PART SELECT, AND FOLLOWED INSTRUCTIONS. VERY SIMPLE REPAIR.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jo Ann from WYLIE, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plunger/magnet capsule fell out of door recepticale because plastic locking tab broke off
Simply inserted new plunger/magnet back into door with thumb&finger until you hear the little locking tabs click. No tools required.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SAINT CHARLES, IL
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking hose
2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- saul from NEW YORK, NY
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Did not draw the water and did not finish its cycle
Remove where the water pumps are and remove the one that was damaged easily
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from S HAMILTON, MA
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leak in top washer hose
Super straightforward to diagnose and repair.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from HIGHLAND, UT
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noticed small tear in hose bellows and leak during reassembly
I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynly from Montrose, CO
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bought used, realized did not have a detergent dispenser.
Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from LA CROSSE, VA
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
soap dispenser broke
just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here
Was this instruction helpful to you?
Thank you for voting!