WM4070HVA (ASSEEUS) LG Washer - Instructions

Watched videos but didn’t show the clamp had to be placed on counterclockwise

Got new door gasket, watched several Youtube videos of repair process. Followed several combinations of the process, which were accurate and it went ok. Met with the described difficulty re-installing the boot due to the spring installation. The use of vise grips for the second spring was the best piece of advice, as the spring tool did not work for that specific process. Door did not want line up exactly the way it came off, causing some concern about the door lock, and possible leaking. After install, it seems to work ok on those accounts. Have only run large bulky items since, which cause many "OE" issues. have not tried a normal load yet, but I think it will be ok.

First I had to elevate the washer on 3-5 gal. buckets in order to get underneath it and find the leak. Then I tried to repair the hose itself-which actually worked-but then the rest of the hose just started splitting everywhere I touched it. So I ordered the new part which took some careful comparing and examination online. But it was exactly the right part. You have to remove the top of the washer which is just 2 or 3 screws. Then taking the hose out was a little challenge-knowing I would have to put the new one back in carefully. Use Vaseline on rubber fitting at the end of the hose that connects to the washer. Need at least 2 people to raise the washer up in air to work on it.

Followed instructions on YouTube link. Replaced the shock absorber and washer is working really well.

I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).

just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here

To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.

Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work

Replaced it

I set my iPad on the exposed washing machine drum, was exposed after removing top as explained in video, and put on the ‘ how to do video it’. It was so easy for this 78-year-old brain, that I am very pleased with myself. Also would like to thank whoever I talked to, Chris, when I ordered this part from this company, Chris was very helpful and took time with me. So this ‘do it yourself person’, and I’m really not a do it yourself person, WILL certainly be looking into other do it yourself fixers. Thank you again.

Removed and replaced unit after turning off the cold water valve. Turned water back on and it worked as it should. I also have to mention the very rapid shipping! Thank you!

It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done

Took off the old hose with a screwdriver and put the new one on. As simple as that. You don’t need a repair man to get this done, you can do it yourself and save money too.

Just like it shows on You tube but one of the shocks did not come with the plastic pegs so i used the old one. I need to order the springs now and replace them.

After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.