Models > WM2350HWC

WM2350HWC LG Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Models for WM2350HWC

Click on the best match to narrow your results.

Diagrams for WM2350HWC

Viewing 3 of 3

Manuals & Guides for WM2350HWC

Click to download
Keep searches simple, eg. "belt" or "pump".
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it ...
In Stock
Order now and your part arrives by Nov 22
Regulate the washer?s hot water supply with this single-solenoid inlet valve. It links the household hot water line to the internal filling system, opening on a control request and closing when the fi...
In Stock
Order now and your part arrives by Nov 22
Hold the door slightly open between loads, allowing air to circulate through the drum and around the door seal with this washer magnetic door plunger. This helps trapped moisture dry and reduces musty...
In Stock
Order now and your part arrives by Nov 22
A rubber barrier around the rotating drum shaft helps protect the washer?s tub bearings from water and detergent. This rear tub shaft seal sits in the rear outer tub, keeping wash water out of the bea...
In Stock
Order now and your part arrives by Nov 22
This front-loading washer door boot seal connects the outer tub to the front panel, using folded rubber to accommodate movement during washing and spinning. A flexible barrier around the washer openin...
In Stock
Order now and your part arrives by Nov 22
This door lock and switch assembly holds the door closed during operation and reports its status to the main control board. Secure door locking allows a front-loading washer to begin and complete its ...
In Stock
Order now and your part arrives by Nov 22
Water leaves the washer tub through this flexible tub-to-pump drain hose before reaching the drain pump housing. Its corrugated bellows section bends with tub movement, helping maintain the connection...
In Stock
Order now and your part arrives by Nov 22
The suspension shock absorber connects the tub to the cabinet base and resists sudden movement as the load turns. A worn or damaged absorber may allow excessive shaking, thumping, or repeated unbalanc...
In Stock
Order now and your part arrives by Nov 22
The motor rotor position sensor monitors the direction and speed of the spinning rotor and communicates this information to the electronic control board. If your washer is displaying an LE error code ...
In Stock
Order now and your part arrives by Nov 22
This rubber tub seal fits between the front and rear halves of the washing machine’s outer tub to prevent water leaks. It helps maintain proper washing performance and may need replacement if you noti...
In Stock
Order now and your part arrives by Nov 22
Liquid detergent stays contained in this removable dispenser cup until water flushes it into the washer during the wash cycle. The blue plastic insert sits inside the main detergent drawer and can be ...
In Stock
Order now and your part arrives by Nov 22
Cold water reaches the washer tub and dispenser through this triple-solenoid inlet valve assembly. Its three controlled outlets open during selected cycle stages, directing water where needed before c...
In Stock
Order now and your part arrives by Nov 22

Common Problems and Symptoms for WM2350HWC

Viewing 19 of 19
Will not drain
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Draining Issues
Fixed by these parts
Fixing Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Locking Issues
Fixed by these parts
Fixing Fixing
How to fix it
Spinning Issues
Fixed by these parts
Fixing Fixing
How to fix it
Water Filling Issues
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing
How to fix it
Does not dispense fabric softener or detergent
Fixed by these parts
Fixing Fixing
How to fix it
Burning smell
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Shaking and Moving
Fixed by these parts
Fixing Fixing
How to fix it
Engine runs but does not pump water
Fixed by these parts
Fixing
How to fix it
No hot or cold water
Fixed by these parts
Fixing
How to fix it
Noisy and Marks Left on Clothes
Fixed by these parts
Fixing Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing
How to fix it
Spins slowly
Fixed by these parts
Fixing
How to fix it
Noisy
Fixed by these parts
Fixing
How to fix it
Not draining
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jorge from Apple Valley, CA
Parts Used:
4681EA2001T
Difficulty Level:
Easy
Total Repair Time:
1- 2 hours
Tools:
Screw drivers
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
592 of 761 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Mark from Harrisburg, PA
Parts Used:
6501KW2002B
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Socket set
LE Error Message and won't spin drum properly
I first tested the motor per the service manual. I checked the resistance between the terminals of the 3 pin connector. It's supposed to be 5-15 ohms. The motor checked out so I replaced the main electrical board. It turns out that wasn't the problem. After a brief web search I found out that the hall sensor (which is attached to the motor stator) was the likely cause of the failure. I replaced that and everything works great now. And now I have a spare main board in case that ever fails. I also want to mention that I took the time to remove the dispenser box (where the water comes in and is directed to the different cleaning products) and cleaned it with a very strong bleach solution. It got rid of the mildew and funky smell. It seems that the fabric softener caused a lot of mildew to form inside the dispenser directly above the fabric softener tray. The bleach took care of that. This is probably something that should be done routinely to keep the mildew from forming.
255 of 339 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Omnitech from Warrenville, IL
Parts Used:
AGM73610701
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins
Door would not close
There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replac e the magnet was $18. Instructions were included in the box. Part number on the drawing was A165. PS3618292 Magnetic Door Plunger
157 of 181 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!