WM2550HWCA (ABWEEUS) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Janice from OVIEDO, FL
- Parts Used:
- 5220FR2008F
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Wrench (Adjustable)
Cold water not shutting off
Unplugged washer.
Disconnected water line,
Removed 2 screws then removed clips for hoses on inlet valve.
Replaced valve and hooked hises back up. Replaced plate or rear of washer and plugged back in.
Works great and even with cost of 1 day delivery, saved at least $200 doing myself.
Disconnected water line,
Removed 2 screws then removed clips for hoses on inlet valve.
Replaced valve and hooked hises back up. Replaced plate or rear of washer and plugged back in.
Works great and even with cost of 1 day delivery, saved at least $200 doing myself.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Philip from WASHINGTON, DC
- Parts Used:
- 5220FR2008F, 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Water continued to flow into machine during drying cycle and afterwards
This was a very easy repair. Just followed the steps in the videos on the website (I replaced both the hot and cold inlet valves, so two different videos, but the process for each is similar) and it couldn't have been simpler.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rosie from SPRING, TX
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Washer door lock would not stay locked; consequently, washer did not run.
Unscrewed 2 screws holding part. Removed old part & replaced with new.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Julius from WINNETKA, CA
- Parts Used:
- 4775ER2002B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers, Socket set
Door Hinges, door lock assembly, frame door
Remove door assembly from the hinge, unscrewed screw from the panel. Leave couple screws to hold Hinges. Remove the rubber seal but stretching to spring out, not having rt tool (long nose plier). Remove rubber partially close to the hinge. Remove the Hinges and replaced it, then reverse putting together back. Use small screw driver to put spring tensioner back. Reinstall frame door to hinge, double check everything.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- saul from NEW YORK, NY
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Did not draw the water and did not finish its cycle
Remove where the water pumps are and remove the one that was damaged easily
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gary from Pine, AZ
- Parts Used:
- 4434ER0002H, 4036ER4001B
- Difficulty Level:
- Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
Noisy Bearings
In order to replace the bearings of a front loader LG Washer you will need to disassemble the entire unit. you should have excellent mechanical skills to tackle this project with necessary tools. Plan on replacing both bearings and rear seal, also plan on replacing the spider and drum seal. The Spider that supports the inner drum will be corroded due in part to seal failure. By the time you are hearing the bearing noise the damage to the spider will have taken place and need replacing. You can watch a few videos on youtube with similar appliances to give you an idea of the project at hand. Once disassembled cleaned and inspected the assembly goes real smooth. The washer now works as good as new and is ready for another 10+ years of service. Doing this project myself has saved me from buying a new one and that savings amounts to over $1000 bucks. LG washers are built to last and you will see that while working on it! Good Luck and do your homework!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wane from OLATHE, KS
- Parts Used:
- 5006ER3022A, 5006ER3021A, 3891ER2003A
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- More than 2 hours
Washer leaks
Could not do the repair. Partselect sent me the wrong parts even though I gave them the model number and the brand they sent me the wrong parts.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Magalys from WYOMING, MI
- Parts Used:
- 383EER3001J
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Washer was giving an error and not removing water/spinning
Followed instructions on YouTube link. Replaced the shock absorber and washer is working really well.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kirk from WEST COLUMBIA, SC
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
washer would not run
replaced switch as shown in the video...Worked great
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from HIGHLAND, UT
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noticed small tear in hose bellows and leak during reassembly
I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from LA CROSSE, VA
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
soap dispenser broke
just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from CINCINNATI, OH
- Parts Used:
- AGL74334828
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Original soap/softener/bleach drawer apparently had a design flaw which allows the drawer to remain stuck inside..
With basic tools,the original drawer was broken up in tiny pieces and removed. The replacement drawer seems to have a little different design and doesn’t hang up internally.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Chris from RIVERVIEW, FL
- Parts Used:
- 5220FR2008F, 5220FR2006H
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Water filling the basin
Water would fill the basin when the washer wasn't used. I followed the video created by this site to make the repair. The video gave me the confidence that I could successfully make the repair myself. The hardest part was physically moving my washer out of its corner to make the repair. The parts were plug and play. Awesome!!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from MARYVILLE, TN
- Parts Used:
- 383EER3001J
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Spin cycle was shaking my house LOL
Just like it shows on You tube but one of the shocks did not come with the plastic pegs so i used the old one. I need to order the springs now and replace them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from FENTON, MI
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer would not drain.
I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.
Was this instruction helpful to you?
Thank you for voting!