WM0642HW (WM0642HW /01) LG Washer - Instructions

Turn off circuit breaker. Turn off water at shutoff valve usually located under sink. Disconnect water line from dishwasher. Disconnect wires for the power feed from cord, Marked corresponding wires upon removal for re-installation. Remove 2 mounting screws that secure dishwasher to counter. Slide dishwasher out from counter and turn upside down. Use a blanket to prevent scratching of surfaces. Locate component on the back portion of the dishwasher. Unplug 2 wiring harnesses. My part was held on by 2 phillip screws. One in front, the other in the back along the leg bracket support. Once removed, reverse the order of removal. The i a You Tube video you can locate fr this removal. They said that you needed to release a clip to get the part out. Mine had a screw holding it on the back side. This difference cause about an extra 1/2 hour before I was able to figure out that there was NO clip that was being shown on the video. After that, The replacement went smoothly and we were having the dishes washed later that day.

you tube it , not to hard to install

Watch the video to repair and follow along

removed top and front. heater is at the base of the tub. the nut compresses the rubber seal and may take some wiggling to remove the old one.

remove 2 screws from top panel - pull top panel back and lift off washer. reach down on front side and remove wire harness that is attached to door lock assembly. remove the 2 screws on front of door lock,remove and replace with new assembly. attach wire harness and then tighten assembly with the 2 screws. replace top of washer panel and tighten with 2 screws.

Just removed the top cover only. Reached down and unplugged the door switch. Then removed the switch with 2 phillips head screws. Replaced with new switch. Reached down and plugged that new switch in. Problem solved!

From previous experiences with other washers, i.e., Sears, I decided it was the mother board or the door latch component. Ordered the electronics and then the discovery that LG has an APP for iPhone. Loaded the app, placed the phone next the washer and pushed the button on the washer. The washer "talked" to the iPhone and within 15 seconds it told me there was a problem with the thermistor. Opened the back of the washer and looked under the tub for the thermistor and found the 2 connecting wires were hanging loose. Put the wires back into the thermistor connection and everything was back working.

Disassembled washer, replaced bearings, seals and gasket. Watched instructional video to familiarize myself with the repair. Followed all steps as recommended, repair was straight forward without any surprises. Hardest part was removing the drum from the machine, somewhat heavy. Disassembled and replaced all bearings, seals, spider and gasket. Reinstalled in reverse order. Note: Upon tear down, I found the seal was pushed out, causing the bearing failure. I also found that the seal was installed incorrectly from LG. They have the seal lip facing the bearings, should be facing the water. This repair seems to be difficult, but was fairly self explanatory. All plug ins are color coded, all hoses are accessible with little effort. If you have basic skills you should be able to handle this repair.

replaced switch as shown in the video...Worked great

I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars

Remove where the water pumps are and remove the one that was damaged easily

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.

Do not pay a service company to come to your house to make this fix!!! If you have common sense, simple tools, a phone camera and some mini zip ties you can do this!

After watching a couple YouTube videos on installing a new motor I had the confidence to start the job. My biggest worry was I'd forget where a screw/part went so I took a lot of pictures as I disassembled. I also laid all the parts out on a table reflective of where they belonged on the machine. I learned washers aren't rocket science - YOU CAN DO THIS. The most difficult part of the fix was my washer was a different model so much of the caging was completely different than YouTube disassembly, but once I got into the machine it was fairly identical. Easily popped out the old, broken motor and inserted the new LG certified part. Reassembled in 1/2 the time of disassembly and my machine works like new:) Hoping to get another 10+ years out of this washer.

Thanks PartsSelect for the high quality certified LG part. Very nice quality and weight.

The video from PartSelect showed removing the retaining ring from the rubber washer tub boot to then allow access the door lock located behind the boot for replacement. That ring can sometimes be a real pain to put back on. This can be avoided altogether!

It's much easier to access the door lock switch by removing the two retaining screws on the top cover of the washer found in the back of the machine. Remove the top cover and you can then reach down to remove the wiring connector, unscrew the two phillips screws on the front of the door latch and remove the door lock. Put the new switch on in reverse order; plug in the connector, replace all screws and the top cover, and you are done! This method took than 10 minutes from start to finish.

Please note that the washer should be unplugged from power while working on any electrical component.

Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.