WM1814CW LG Washer - Instructions

Unscrew door and insert. Replace hinge. Screwed in. Replaced insert then door. Gave it lite slam. I took longer cleaning lint and glass. I too should be a repairman.

I removed the top off the washer, unplugged from the electrical, removed the three hoses and wiring plugs, removed the two screws holding the valve assembly in place, and replaced the part with the new. It was a very simple swap, and I even found a video on YouTube on how to replace it.

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

First we unplugged the machine. Then turned off the water and disconnected the hoses. Pulled out the machine and laid it on its side to access the themsistor located on the drum. (No, you do not have to remove the control panel at all to replace this part) The thermsistor is clearly seen with a flashlight. There were plastic ties holding the wires of the thermsistor so we used small scissors to cut the ties. Then unplugged the old thermsistor and plugged in the new thermsistor and used a regular bag twist to secure the wires. Repair complete and the machine is back to normal. Thank you Part Select.

After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.

Our washer and dryer was stacked, and had to remove the dryer to access top of washer. This took 2 people and was not difficult due to the 168 lb weight of the dryer. Turned of water, pulled washer away from wall and disconnected the supply hoses. Removed the 2 screws holding the top, slipped it back and removed. Removed the 2 screws holding the inlet valve assembly, unplugged the wiring harness from the 3 solenoids, disconnected the 3 hoses from the hose bibs on the valves. Mounted new valve assembly, connected hoses making sure that clamps did not touch any other hoses, reconnected wiring harness, turned on water to check for any leaks, put top back on and tried washer out. Changing the valve assembly took a total of 15 minutes. Really simple. The You tube video very helpful in determining how to do the job.

took out the drain pump and replace with a new one

It was so easy. i searched my model it brought up this site and the most common problem popped up without my even asking and recommended the part. i got it one week later and it was so simple to fix. a repair man wanted three times the part price to come to my home twice and would have had to wait longer. you guys were very helpful

Disconnect electric and remove top cover and remove connectors and hoses then the valves

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

Extremely easy--remove two screws in the back of washer connect elec. connections one at a time connect cold water lines one at a time and replace the two screws ion the back and you are done. Took longer to pull washer out from wall and push back than it did to replace part. Saved me $75.

unplug washer and disconnect inlet and outlet hoses. drain water from washer (about 2 gallons) by removing lint screen from front of washer. lay washer on side (I used a blanket to avoid damaging the paint) remove all the phillips head screws in the plastic bottom and the metal feet of the washer. Gently pull the bottom of the washer off. There are 3 shock absorber looking things that pull apart and are greasy. Try not to mess with them much. Just pull gently, and they slide apart. cut the zip ties holding the wires to the washer bottom piece. remove the screw in the lint screen area and gently pull the recessed plastic thing out the front of the washer. remove the screws holding the pump assembly on the front of the washer. Remove the three screws holding the pump assembly on the outlet pipe manifold. Installation is the reverse of removal, take care to put the shock absorber looking things back in gently and together at the same time when reinstalling the plastic bottom of the washer.

Conclusion was that either the control panel or the noise filter (an electrical fuse apparatus)was bad. Disconnected the water line, turned off power, and pulled unit out from cabinets. Determined that voltage was going into the noise filter (white harness) but almost no voltage coming out (red harness). Ordered noise filter. Hardest part was removing old noise filter from dishwasher frame without removing the whole unit from cabinet and turning upside down.One screw holds the part in the frame. With power off, I used a very small ratchet with phillips screw driver. Pried unit out with screw driver on side to the panel front. It has a retaining tab there.Installation was the reverse. Instead of putting screw back the way it was originally installed, I screwed it in from the outside of the frame. Much easier and just as solid. Tested unit with power on. Hooked up water line. Works great. Note: LG dishwahers have a high repair rate and that this part has a high failure rate. This LG unit was two years old. Never had to fix my 15 year old Sears dishwasher. It still works to this day. (I gave it to my daughter.)

Loosened hose clamps to remove old bellows. That seemed simple but was awkward reaching into the confined space. Clamp adjustments were all installed facing away from access opening. New one went on easy and I reinstalled clamps facing the opening. Perfect fit!

First I turned off the hot and cold water supply and removed the water lines from the back of the machine. I then unscrewed the 2 phillips head screws on the back of the washer for the cover. I slid the cover back and lifted it off the machine. Next, I unscrewed the mounting screws from each inlet valve assemble located on the back of the machine by the hose connections. I used pliers to pull the hose clamps back from the inlet valve, 1 at a time, then reconnected each hose and clamp on the new inlet valve. Once each hose was connected to the new inlet valve, I discarded the old inlet valves. I then re-attached each inlet valve. I placed the cover back on the machine and secured with the 2 screws, re-attached the water supply hoses to the hot and cold side and turned the hot and cold water supply back on. Everything successful, no leaks, and washing laundry again..........leak free!