WM2077CW (WM2077CW /01) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jason from S HAMILTON, MA
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leak in top washer hose
Super straightforward to diagnose and repair.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ryan from HIGHLAND, UT
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Noticed small tear in hose bellows and leak during reassembly
I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.
5 minute job, if the washer top is off (which is also simple).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Roger from LA CROSSE, VA
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
soap dispenser broke
just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lynly from Montrose, CO
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Bought used, realized did not have a detergent dispenser.
Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ALEX from TULARE, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Wrench (Adjustable)
Washer was not draining
It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from COLUMBUS, OH
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver
Broke cold water inlet while moving
Replaced cold water inlet. Removed 4 water lines and 5 wires put new part in and reinstalled lines and wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lauren from CARLSBAD, CA
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Door lock was unable to disengage - couldn't open washer door after cycle. Would cycle constantly through three clicks and be unable to open the door. Eventually had to unplug to get it to stop clicking constantly, and after some careful prying, able to release the door to access the screws we'd n
Watched the easy video instructions on the product page and did the same on our machine - pop off the top, unscrew the plate from the front of the door inset. Its a little challenging to unplug the old lock assembly because it is a tight fit and not enough room for two hands to fit to provide a bit more leverage when pulling the power lines out, but once its out it is easy to install the new one and reattach the strike plate frame and top of the washer. Plugged back in and we were back in business. This $50 part ended up saving us at least $300 in repair fees to get it working again.
Incredibly fast shipping - arrived in less than 2 days - which was really helpful as we were unable to use the washing machine until we were able to get this fixed. Excellent pricing as well. Couldn't be happier I found this site and the product I needed so easily.
Incredibly fast shipping - arrived in less than 2 days - which was really helpful as we were unable to use the washing machine until we were able to get this fixed. Excellent pricing as well. Couldn't be happier I found this site and the product I needed so easily.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jennifer from MARYVILLE, TN
- Parts Used:
- 383EER3001J
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Spin cycle was shaking my house LOL
Just like it shows on You tube but one of the shocks did not come with the plastic pegs so i used the old one. I need to order the springs now and replace them.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Robert from GOLD BAR, WA
- Parts Used:
- 3891ER2003A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Soap dispenser
Replaced it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rick from KERRVILLE, TX
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers, Screw drivers
Hot water valve was leaking
After I watched the repair video for the part, it was a snap. It went exactly as the video described the steps. Hardest part was moving the washer to get behind it.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from CLEVELAND, TN
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
The hot water inlet valve started to leak.
To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from FENTON, MI
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Washer would not drain.
I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Rudy from SAN DIEGO, CA
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Hot water inlet had leak, kept filling washer, when offw
When to utube typed in my problem, very easy fix
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Leslie from ORLAND HILLS, IL
- Parts Used:
- 383EER3001J
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers
Could not remove one of the pins
Removed the front and rear covers ,the control panel , removed the shock absorber pins and shocks installed new shocks and reassembled
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christen from HUMBLE, TX
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
The hot water valve was leaking
It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.
Thank you again for an amazing experience.
Was this instruction helpful to you?
Thank you for voting!