WKE100HWA (ABWEUUS) LG Washer - Instructions

I actually went to mr fix it on u tube. Great instruction on how to take dryer apart. First I unplugged the dryer. I found I could reach the heating system by removing the lint tube in the back of the dryer. I put my I phone with the light on inside the back of the dryer and tested the connections to see if all were working. The thermal fuse was not working. I removed the two wires , red on top and white on the bottom. Then used a small Phillips screwdriver to remove the two mounting screws and removed the fuse. I then used a vacuum to clear any lint from the back of the dryer and inside the dryer. This took me about an hour and a half. I did it this way because I did not want to disassemble the entire dryer to get to the components. I received the fuse in 3 days and tested it. It was fine. I then put it in the dryer screwed it in place, connected the wires. Replaced the lint tube. This took about 10 minutes. Dryer is running great.

I unplugged the dryer and disconnected the vent.
I pulled the dryer away from the wall so I had room to work on it.
Pulled the top cover off (slides back).
Took the door off
Took the front adjustable feet on the bottom off
Unscrewed all of the face screws on the front of the dryer
Took the two screws off of the back of the control panel holding the control panel to the metal frame.
Gently pulled on the control panel to reveal 4 screws under the control panel to be able to take the front cover off.
Pulled the front cover off (the dryer door front cover).
Pulled the dryer vent cover off (two screws).
I could now see the heating element with sensor/fuse (right side).
Did a continuity test (beep) on all visable sensors/fuses on the heating element. No beep on the thermal fuse (used website diagram to locate parts to test and replacement part numbers).
Got the part after about a week, tested the parted (it beeped), replaced with new part and put dryer back together, plugged in and the dryer heated. Problem solved.

The first thing I did was locate a copy of the Service Manual (not the User / Owner Manual). After looking at that and looking online I learned that there is no sensor for the Flow Sense feature itself. The Flow Sense doesn't detect a blockage. It detects excessive heat and the manufacturer has simply concluded that too much heat is most likely caused by a blocked duct and then it activates the Flow Sense safety feature: cutting off the heat source. Since I knew it was a heat problem I figured I'd get inside and check the two thermostats and the igniter. Igniter was fine, one thermostat was fine, the other one - the High Limit Thermostat - was giving inconsistent readings. I replaced it. Here's how: First I took the dryer apart. This is a little time consuming. There are a lot of parts that need to come out. I recommend that you put the screws in small baggies with a note as to where you took them out of so that you know where they go when you put it back together. You need to remove part of the back, the top and the front. I removed the electrical box because that is what is shown in the manual but I'm not convinced that I needed to. See if you can get the rest of the dryer apart without removing it but if you have to remove it it's not that big of a deal. It's a little tricky to detach the wire harnesses is all. And extra steps, of course. I did not remove the drum. Instead I just reached inside with the front off and pulled the wires off the thermostats to test them for resistance with a multimeter. It was kind of a pain and a little awkward but I did not want to mess with the drum tensioner. Once I figured out that the High Limit Thermostat was the likely culprit I removed it - which required a very short Phillips head screw driver and some patience since I could not actually see one of the screws. But all good. Just remember which wire goes on which terminal. Make a note for yourself: gray back / red front - something like that. Then I ordered the part and installed the new one and rebuilt the dryer in reverse from what I did.

Now, here's the thing: I actually did two things: aside from changing the thermostat I also thoroughly cleaned out the dryer. Somehow a lot of lint built up in there - no idea how since it all appeared to leave the dryer through the vent. but there must be some small gap somewhere. I cleaned everything including the flame detector. When I put it all back together it worked but I'm not 100% sure that the thermostat was bad. It's at least possible that all the lint and dirt was messing with the way the thermostats behaved. So what I would recommend, if you have this problem, is to clean it out first and then put it back together enough to run it and see of the heat comes on. It will take maybe 30-60 seconds for the heat to come on while the igniter lights. If not, go ahead and replace whichever thermostats or other parts you think are broken.

Called Parts Select and assisted me in proper parts needed. Drier works as new.

Took out drum. Found all parts easy to locate. Found defective part and replaced with new one.

Thank you Parts Select for your assistance.

1. Had to find out what was causing the problem by eliminating each part one by one using a multimeter. I got a video link from parts select on how to do this.

2. Then got another video link sent to me by parts select on how to take my dryer a part and replace the part.

3. Followed it step by step and it worked really well.

4. The process was great except shipping was excessively high for such a small part.

Wife called me and said the washing machine just flooded the Landry room. I looked at it and didn't see anything wrong. Took the top off and the back off and started looking for a leak, did not see anything. Took the front part of the washer apart thinking the drain hole was plugged up where the rubber boot is. It was ok after taking the big rubber boot off or whatever that is called i was not getting anywhere. I put it back together left the top and the back off. I turned the water on and started the washer on a quick cycle looking for a leak. I found the bellows at the inlet had a small leak fixed that and started the washer again. So what i found out was the clean out drain plug was not in tight letting water out as it was washing after i tightened it all was ok. So i did find a leak that was small that we never saw. The hardest part was putting that wire clamp on the rubber boot it took two people to do that.

I removed the Wire and spring from the tub seal and then removed the seal on the side of the washer that contains the Door switch. I removed the two screws that held the door switch in place while holding the switch with my other hand. Once the screws where out I pulled the switch assembly out thru the gap and removed the wires from old assembly. I then plugged the wires into the new assembly aligned the holes up and put the screws back in the new door switch assembly. I then put the door seal and tub seal holder back on. This took about 15 minutes. I do recomend that you unplug the washer before starting this process.

I'm not for reading instructions. So I just dove right in and took the dryer apart to get down to the motor. I gave the dryer a thorough cleaning and replaced the 3 parts I ordered from the online recommendation. Wish I would have ordered 2 sensors and the 2 thermostats that are near the burner. Just so replace beings I was in there. Replacing the parts was easy, found them just by looking for matches to the new parts. Reassembled the dryer, dont think I put a single screw back where I got it lol. And still haven't put the top lid back on due to difficulty. Not sure if I even needed any parts, found a nest in my outside vent completely plugging it. But after a good cleaning and replacing the parts the dryer dries the best it has since we've owned it. The dryer came with our house which we bought 3 years ago and it was 2 years old when we purchased the house, so it is now 5 years old.

Replaced thermal fuse

I took the dryer apart. You have to take the top off, then the door/front off. There are wires & other parts that need to be unhooked as well. A flat tip screw driver can be used to pop the top off. The screws were all phillips. Once you take that all apart, then you can access the drum. I bought the belt because I thought that was what was wrong with it. Turned out to be hair in the drum rollers. Took those all off & put wheel grease on each of them, put new belt on (since I had it LOL) then put it all back together. Make sure everything is lined up correctly otherwise you will have to take it apart & reline (which I had to do)
I am a 49yr old female & was able to do this repair on my own!

order start button and was sent thermal, reordered and rep sent me a button that was not for my machine even though she had model no.,called third time and was told I had to order new control panel but they were not being manufactured any more.so it is not fixed

To put the new spring on requires two people. One to pull the drum up as far as possible and hold it in place and the other to attach the spring to the drum and the into the slot on the side of the washer frame. It takes a lot of leverage and strength to get the spring into the slot. We used a screw driver as leverage to get the spring extended to slip into the slot. You might also need the plastic holder part# 4930FR3040A. If the washer door boot has come off due to spring breaking, you will need to reset it. That requires also removing front panel. There is a large wire ring that holds the boot in place. You either need a special pair of pliers to expand the spring to reset the boot or a lot of strength to do it with a couple screw drivers.

Entered dryer from rear exhaust port. Removed 2 screws and 2 clip on wires. A little awkward of process but superior method over disassembly of drum and main parts.

Pull off the top and front of the dryer and reached in and replaced the part it was easy. Had to clean all the dryer out real good with from the lint

Initially replaced igniter. Didn't think it was bad though. Read other suggestions on another website. None were the correct diagnosis for my situation. And when I figured it out they did not offer correct part. The dryer thermistor temp sensor (probe sensor) is what I replaced. Found it on Parts Select. I did replace other parts also. But that's the one that ultimately was the issue.
Was not hard at all if one is even a little handy.