T1483EFFTW (ABWETEU) LG Washer - Instructions

Popped out the plastic "doors" that cover the metal actuators. Removed the metal actuators on both right and left sides of the door then unscrewed (3 screws each actuator) them from door frame. Slid the actuators out to enable the door to be removed. Unscrewed 2 screws on the top front of the washer which enabled me to angle the top of the washer to expose the screws that hold the plastic hinges. Unscrewed the hinges (2 screws each) and replaced both of the hinges (I figured I'd do both of them now so I don't have to do it again for another 15 years). Put everything back together and all works like new.

On repair of (replacing one of the MEF62462103 hinges) the previous comments and instructions were good and fairly accurate. However, in addition to having to remove the two screws on the top front so the entire top assemble can be lifted, there are two short screws on the back of the washer towards the top on each side that need to be removed. That way you can tilt the entire top up enough to get to the two underneath phillips head screws for each hinge. It’s okay to leave all the hoses connected and good to have a second person hold the top tilted up so you can get to the hinge screws. It took about 30 minutes to change one hinge for me and my helper.

Looked on line for instructions, took my time and the repair went very easy. Just be careful not to drop screws in tub.

I had a hard time removing the agitator, had to get thin prybar to get a hold of washplate. After I removed washplate, I found that the shaft that the washplate attaches to was actually worn out. What used to be a spline was smooth. So I ordered a new clutch assembly. There are a lot of bolts that hold the clutch assembly on to the basket. There are a lot of videos on Utube that will walk you through step by step. The only problem I encountered with this was removing the nut that holds the basket to the tub. One video said it was reverse thread, which it wasn’t. You can check the thread on new clutch assembly to see which way is correct. After I put back together. Works like new.

Removed flimsy, easily breakable panels (one on each side), that cover the hinges for the top lid. Removed screws that cover the pins in the door top, that fit in the swivel. Removed broken door.

Placed pins in new door into swivel brackets, replaced covers that hold the door correctly in place. Tightened in place with screws. Pot panels back into pace to cover the swivel mechanism.

Job complete.
Sorry for the written confusion, don’ see a way to attach photos that make it simple to understand.

The instructions received from partselect.com were really good. There are two long screws located on either side of the front control panel. Simply removed the small covers to expose the two screws. Then remove both screws. At that point you can lift up (carefully) the front panel high enough to gain access underneath to remove the two Philip head screws holding the hinge. Be careful not to drop the screws down in the machine cavity. Lift out the old hinge and insert the new one. Re-install the two Phillip head screws into the new hinge. Let the front panel back down and re-install the two long screws. You’re done!

Description provided on website was that repair was similar to another washing machine where you press in on spring clips to release top of machine to access hinge. Not correct at all.

There are two screws on top of machine that are covered by caps. Remove caps and then remove screws. Lift up / prop up machine top and you have easier access to 2 screws that hold plastic hinge in place. Remove screws and replace hinge and replace screws. Took me longer to figure out I had incorrect directions than it did to replace hinge.

Removed 2 hidden screws from the top panel.
Lifted top panel.
The first screw came out easy, the second one gave me trouble.
It is best to help a helper who can hold the lid open as much as possible.
To insert the new screws takes patience as they might fall very easily.
Overall, not that difficult - just need patience.

raised the front of washer by hand (literally) and placed two 2x4 blocks under front lip for support. reached up inside washer cabinet and unscrewed the broken leg piece upwards into the cabinet. this was the only way I could get the broken piece out without some specialized tool to reach it from the underside. replacement with the new leg was a breeze.

Remove cover over associated hinge pin assembly and the hinge assembly behind it. With the lid open, remove 4 screws holding on the top assembly, lift and rotate it on its wire cable side and rest it on the machine top frame (it may be necessary to remove the 2 cable restrainers to gain enough play to do this - you will have to remove the large rear cover to accomplish this and be able to reinstall these restrainers). Remove 2 screws fastening the broken hinge pin receptor, install new unit, and fasten with these 2 screws. Install top assembly and a new/repaired hinge pin assembly (most likely the reason for the broken hinge pin receptor).. Replace cable restrainers and rear cover if it was necessary to remove them. Note: These hinge pin assemblies are sold as a set (1 left, 1 right; they are not interchangeable and are expensive). Time to do repair = about 30 minutes.