T1475HGPV (ABWEVUS) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- David from SHELBY TWP, MI
- Parts Used:
- MEF62462103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Plastic hinge broken on RHS.
Description provided on website was that repair was similar to another washing machine where you press in on spring clips to release top of machine to access hinge. Not correct at all.
There are two screws on top of machine that are covered by caps. Remove caps and then remove screws. Lift up / prop up machine top and you have easier access to 2 screws that hold plastic hinge in place. Remove screws and replace hinge and replace screws. Took me longer to figure out I had incorrect directions than it did to replace hinge.
There are two screws on top of machine that are covered by caps. Remove caps and then remove screws. Lift up / prop up machine top and you have easier access to 2 screws that hold plastic hinge in place. Remove screws and replace hinge and replace screws. Took me longer to figure out I had incorrect directions than it did to replace hinge.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Heinz from SARASOTA, FL
- Parts Used:
- MEF62462103
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
RIGHT HINGE BROKE
Removed 2 hidden screws from the top panel.
Lifted top panel.
The first screw came out easy, the second one gave me trouble.
It is best to help a helper who can hold the lid open as much as possible.
To insert the new screws takes patience as they might fall very easily.
Overall, not that difficult - just need patience.
Lifted top panel.
The first screw came out easy, the second one gave me trouble.
It is best to help a helper who can hold the lid open as much as possible.
To insert the new screws takes patience as they might fall very easily.
Overall, not that difficult - just need patience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from EDWARDS, IL
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
very dirty under adjitator cap and pulsator
Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- John from TUCSON, AZ
- Parts Used:
- MEF62462103
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
Lid hinge pin receptor (MEF62462103) broken
Remove cover over associated hinge pin assembly and the hinge assembly behind it. With the lid open, remove 4 screws holding on the top assembly, lift and rotate it on its wire cable side and rest it on the machine top frame (it may be necessary to remove the 2 cable restrainers to gain enough play to do this - you will have to remove the large rear cover to accomplish this and be able to reinstall these restrainers). Remove 2 screws fastening the broken hinge pin receptor, install new unit, and fasten with these 2 screws. Install top assembly and a new/repaired hinge pin assembly (most likely the reason for the broken hinge pin receptor).. Replace cable restrainers and rear cover if it was necessary to remove them. Note: These hinge pin assemblies are sold as a set (1 left, 1 right; they are not interchangeable and are expensive). Time to do repair = about 30 minutes.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristen from Safford, AZ
- Parts Used:
- AGZ72909711, 5006EA3009B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Washer pulsator was coming loose during wash cycle.
Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from THOMASTON, GA
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
could not get the 10 mm nut to loosen
Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had
Was this instruction helpful to you?
Thank you for voting!