Models > F1399RYN

F1399RYN (ABWEEUS) LG Washer

Jump to:

Find Part by Name

Diagrams for F1399RYN

Viewing 4 of 4

Most Popular Parts for F1399RYN

Viewing 12 of 136

Water Inlet Valve - Hot

★★★★★

(2)

$34.97

The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with wat...

Order now and your part arrives by Mar 19

Magnetic Door Plunger

★★★★★

(3)

$18.85

This magnetic door plunger is a genuine replacement component designed to keep the washing machine door slightly ajar when not in use. By allowing air circulation, it helps the inner door and tub seal...

Order now and your part arrives by Mar 19

Tub-to-Pump Drain Hose

★★★★★

(1)

$54.01

This hose has bellows to allow for flexibility during the wash and spin cycles.

Order now and your part arrives by Mar 19

Shock Absorber Kit

$41.15

This kit includes 1 shock absorber and 2 pins.

Order now and your part arrives by Mar 19

Washer Gasket

$24.10

This rubber tub seal fits between the front and rear halves of the washing machine’s outer tub to prevent water leaks. It helps maintain proper washing performance and may need replacement if you noti...

Order now and your part arrives by Mar 19

Detergent Dispenser

$24.10

If your washer isn’t dispensing detergent or fabric softener properly, this replacement container assembly may be the fix you need. Designed to hold liquid cleaning agents and release them at the righ...

Order now and your part arrives by Mar 19

Drain Hose Assembly

$36.00

Order now and your part arrives by Mar 19

Locking Pin

$20.95

The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.

Washer Hinge Spring

$46.30

Order now and your part arrives by Mar 19

Clamp Assembly

$20.95

Order now and your part arrives by Mar 19

BOLT ASSEMBLY

$18.85

Clamp

$14.65

Order now and your part arrives by Mar 19

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for F1399RYN

Viewing 12 of 12

Leaking

Fixed by these parts

How to fix it

Lid or door won’t close

Does not dispense fabric softener or detergent

Noisy and Marks Left on Clothes

Fixed by these parts

How to fix it

Videos for F1399RYN

Viewing 7 of 7

Replacing the Magnetic Door Plunger

Replacing the Water Inlet Valve - Hot

Replacing the Shock Absorber Kit

Replacing the Washer Switch Assembly

Replacing the Tub-to-Pump Drain Hose

Replacing the MOTOR

Replacing the Detergent Dispenser

Installation Instructions for F1399RYN Provided by Fix customers like you

Viewing 3 of 84

Customer:: Omnitech from Warrenville, IL
Parts Used:: AGM73610701
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins

Door would not close

There is a magnet at the bottom of the door which allows the door to be held ajar when the washer is not in use to allow the tub and gaskets to dry. A tab on the plastic housing which retains the magnet broke which allowed the housing to pull free of the door and stick itself to the machine preventing the door to close. Easy fix to replac ... Read more

Read less

157 of 178 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Leslie from STOWE, VT
Parts Used:: 4738ER1002A
Difficulty Level:: Easy
Total Repair Time:: 30 - 60 mins
Tools:: Screw drivers

leaking tub-to-pump drain hose

Pull washer away from wall. Unplug cord and remove drain hose from receptacle. Remove 4 screws holding panel to rear of washer. Squeeze and slide back hose clamps on each end of drain hose and loosen center clamp with screwdriver. Remove old hose. Reinstall new hose in reverse order using existing clamps. Re-install back panel.

51 of 71 people found this instruction helpful.

Was this instruction helpful to you?

Customer:: Sanjay from HOLTSVILLE, NY
Parts Used:: 5220FR2006H
Difficulty Level:: Really Easy
Total Repair Time:: Less than 15 mins
Tools:: Pliers, Screw drivers, Wrench (Adjustable)

Water was filling continues even the machine was unplugged

I did repaired while looking at video at your site .thanks to your team ..

20 of 24 people found this instruction helpful.

Was this instruction helpful to you?