F1387FDS (ABWEEUS) LG Washer - Instructions

1. Unplugged electric chord from wall.
2. Pulled washer out into open area to get behind it.
3. Turned off hot and cold water faucets
4. Used channel locks to remove hot water and cold water hoses from back of washer. Dropping hose into a bucket to catch water from hose.
5. Removed screws (Phillips screw driver) holding top to back of washer.
6. Pulled back on the top and lifted off washer.
7. Arranged new intake valve to mock location and setting of old intake valve.
8. Using Phillip screw driver, unscrewed old intake valve from back of washer.
9. Unconnected wiring from old intake valve. These were easily identified and not needed to mark left right center.
10. Using pliers, pinched hose clips and moved to middle of the hose. Did this for all 3 hoses.
11. Removed hose from old intake and connected to same location on new intake. Repeated for all 3 hoses.
12. Using pliers, pinched the clips and moved to the end of the new intake valve. Did the for all 3 hoses.
13. Using Phillips screw driver, screwed in the new intake valve where the old intake valve was located.
15. Inserted the wiring connects into new intake valve.
16. Reconnected water hoses back into washer machine (after inspecting and cleaning plastic strainer traps)
17. Turned on water faucets
18. Plugged in washer.
19. Ran an empty load for a cycle.
20. Did not fail.
21. Reattached top to washer. Laying down an inch from front and push forward to hear a click or lock. Then screwed in the 2 screws.
22. Pushed washer back into original location.

We have already performed 1/2 dozen loads.

I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).

Followed instructions on YouTube link. Replaced the shock absorber and washer is working really well.

Could not do the repair. Partselect sent me the wrong parts even though I gave them the model number and the brand they sent me the wrong parts.

With my wife's help( 2 shoukder surgeries ), pulled it forward, unplugged power source, turned Both water supplies off.
Removed two phillip screws from each upper ( plastic) holder.
Bumped top from front( works really well if you can use both arms,and with rubber gloves on for traction, or go to harbor freight purchase a glass suction cup) .
I marked ( with a sharpie) the solenoids/hoses,and wires, ( facing front ,right to left,1,2,3.), removed plugs,loosened clamps and pushed them back,gave each hose a twist,and removed them.
Took two screws 5/16 from the back that hold the valve assembly in out.
Removed old valve assembly, put new in place, reverse procedure for assembly. Once all is hooked up,and water dried, I plugged in,turned water on watched for two cycles( you need not stand over it,if it leaks you will know it) to double check, installed top,and we pushed it back in place.
Very simple to do,these washing machines are so easy to work on.
Now we enjoy a dry laundry room,and you can to.
??

When to utube typed in my problem, very easy fix

I removed the top of the washer, pried the front control panel off (pull a couple of electrical connecters or just rest it on something), separated the tub sleeve from the front panel and then removed the front panel (two screws). To remove the pump - just remove a couple of hoses, two wires and slide it out of the clip below. Reverse the process to install. A little daunting if you haven't done something like this before, but easily do-able once you get past your fears. A service call would cost much more than the $60.00 it took to get the part to my front door. This worked out really great - my wash smells fresh once again and my wife has moved on to the next project on her honey-do list!

Removed the front and rear covers ,the control panel , removed the shock absorber pins and shocks installed new shocks and reassembled

I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.

Just like it shows on You tube but one of the shocks did not come with the plastic pegs so i used the old one. I need to order the springs now and replace them.

Watched video on U-Tube , unplug power cord, turn off water, take top off washing machine, remove water hoses, unscrew parts, remove hoses with pliers, install replacement parts, put all back together. Does not leak any more !

Replaced it

Took off the old hose with a screwdriver and put the new one on. As simple as that. You don’t need a repair man to get this done, you can do it yourself and save money too.

It was giving me a code got on YouTube it gave the code after that bought a new pump and fix done

Looked at videos on line at Parts Select. Very easy instructions to watch and follow. After unplugging the washer all I had to do was turn off the cold water valve, remove the supply line, two screws to get the lid off, then two screws to remove the valve and disconnected the electric connector tabs. Took pliers to back the three hose clamps off. The best tip was replacing each hose back on the valve one at a time to prevent mix ups. I did everything in reverse after installation. I ran one short cycle to test the leak. Works perfectly!
A tip I saw on You Tube - I have vinyl flooring in my wash room and a repair guy said to spray a light shot of WD 40 under the feet. It doesn’t take much. Man, my washer slid like it was on wheels! I wiped away any excess spray and let it dry under the feet. I’m not sure how this works on other types of floors.