F1305FDM (ASTEEUS) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Gary from CPE GIRARDEAU, MO
- Parts Used:
- EBF49827801
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers
Would not run
I followed the instructions of your instant repairman. A Phillips screwdriver was the only tool needed. Thank you .
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Steven from KREMMLING, CO
- Parts Used:
- 4681EA2001T, 5215ER2002G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Not draining water from tub.
Honestly youtube but pretty simple install.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- gregory from TEWKSBURY, MA
- Parts Used:
- 6501KW2002B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
would not spin le code
bought a position sensor
top load machine when i tipped the machine over i found
the nut and washer on the floor .replaced the sensor and nut
took about half an hour
top load machine when i tipped the machine over i found
the nut and washer on the floor .replaced the sensor and nut
took about half an hour
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from RIO RANCHO, NM
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Washer not pumping out and making ominous noises
Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry G from FORT WORTH, TX
- Parts Used:
- 383EER3001J
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Excessive vibration
I followed the video -- to take apart and reversed the steps to re-install. It was fairly straight forward and corrected the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Greg from ENUMCLAW, WA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Water pump went out.
Watch the video to repair and follow along
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from ROSEVILLE, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Noisy and drum still full of water . Will not go to next cycle.
Follow the LG washer video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- CHRIS from BAY CITY, MI
- Parts Used:
- 4681EA2001T, 4986ER0004G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Bellow was old and pump was making noise
Disconnected power, removed top cover, removed control panel, removed door assembly then was able to access and replace the bellow and pump.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from WASHINGTON, DC
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
w/d repeatedly fills with water during warm or hot loads
E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Livonia, MI
- Parts Used:
- 383EER2001A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The pump filter leaked after cleaning it out. Would work with teflon tape, but wanted to see if a new part would eliminate the need to wrap it every time.
Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from FLORENCE, MA
- Parts Used:
- 4866ER0007B
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Lower Balance Weight Broken Concrete Internals
The web interface is nice, however in this situation it references the wrong part which was not known until the item arrived. Customer Service handled return, however I had to call LG directly to confirm correct part number (LG p/n 4866ER0004A = p/n PS3524040) but this was only after LG also gave wrong p/n. When replacement part arrived the internal concrete had a crack in it. The part is basically a plastic shell that is filled with concrete. However the opening (about 1 x 4) is left open and with the concrete having a crack in it the piece will vibrate together and continue to break down over time (which is what happened to the original one) Before installing I chose to fill opening with epoxy and a plastic layer, then covered with electrical tape to seal it in. I feel this item is poorly designed from LG. Additionally this item was poorly packaged by PS when shipping which caused the damage (it weights about 15 lbs and was allowed to float around in a large over-sized box filled with large air pillows). I have photos but no way to upload here.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Todd from LAKEWOOD, CO
- Parts Used:
- 4930FR3040A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Drum spring broke
Removed top panal found broken parts and pieces, replaced spring and plastic spring holder. Straightened out and reattached drum front boot.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jack from SAN ANTONIO, TX
- Parts Used:
- 5220FR2008F, 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Screw drivers
Water was slowly filling up in washer tub, after I would wash clothes 2 or 3 days later there would be water standing in the washing machine.
I looked this problem up on YouTube like I do with everything, I saw a video from this site.. so I ordered what I needed from the website. The parts came in I unpluged the washer from the wall very important, I literally removed 6 Philips head screws and unclipped the wires from the parts and removed the hoses with the pliers, hoses have squeeze clamps. Put in New parts put hoses back on wiring back on and I was done.. it took me a total of maybe 10 minutes.. NO MORE WATER standing in the washer.. Thank you!! I would recommend you add a video for the Inlet Valve Assembly like you have for the hot inlet valve though...
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from CONESUS, NY
- Parts Used:
- 383EER3001J
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer shook in spin cycle
Took front of machine off to access 2 shocks, put back together then removed panel in back to access third shock, watched YouTube video first so things went smooth
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from DENVER, CO
- Parts Used:
- EAU61383518
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
leak from bottom front left.
Disconnect washer - pull out and turn on it's right side. Remove bottom plate (2 screws). Water intake valve is attached to water line. Disconnect water line. On the other end of the pump is a rubber hose. Disconnect hose by using a pair of pliers to open pipe clamp. Disconnect the electric line by pulling the pronged plug out of the pump. The part is composed of the pump and a metal mounting plate. They are connected by 4 screws. Remove the screws and pull out the back half of the pump. The front of the pump is attached to the washer frame by 2 screws. When removed you will notice an o-ring that forms the seal between the two halves. Remember this when installing the new pump. You will have to take the new pump apart because the whole part will not fit through the frame opening, thus the need to make sure the o-ring is properly seated. You can either install the mounting plate to the frame then attach the pump half or with half of the part in front of the frame and the other half behind the frame connect the two, then attach it to the frame. Reconnect incoming water line using teflon tape and a crescent wrench. Reconnect out-flow line with the pipe clamp and attach the power line. Since you have to take the new pump apart make sure the o-ring is properly seated as it will have a tendency to fall out. Reassemble the rest.
Was this instruction helpful to you?
Thank you for voting!