TCW2013CS1 (ASSEELC) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Kenneth from CONESUS, NY
- Parts Used:
- 383EER3001J
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer shook in spin cycle
Took front of machine off to access 2 shocks, put back together then removed panel in back to access third shock, watched YouTube video first so things went smooth
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- stephen from FRANKLIN, NJ
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
washer dicharge water pump
you tube it , not to hard to install
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joshua from DELTA, PA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers, Screw drivers
Error Code OE showed drain pump problem
I youtube searched this problem and found a video from partselect. I watched the video, purchased the part, and followed the video instruction step by step to repair the washer. Part with tax and shipping was $52.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gloria D. from MEMPHIS, TN
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
broken retainer
pops right into hole
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jason from S HAMILTON, MA
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Leak in top washer hose
Super straightforward to diagnose and repair.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
There was puddle under the washer.
I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.
Two hose clamps to remove and replace, then replace the top and ready to go.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from SAINT CHARLES, IL
- Parts Used:
- 4738ER1004B
- Difficulty Level:
- Very Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers
Leaking hose
2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anne from MONROE, NY
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Magnetic door plunger broke off, then got stuck inside the door and couldn't be removed for replacement.
I used another magnet to pull the old plunger out of the door and replaced it with the new part.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Larry from IOWA PARK, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Door plunger had a broken tooth and would not stay in place.
Just put in the new one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Andrew from BOTHELL, WA
- Parts Used:
- AEG33121501
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set
TE error. Replaced heater / thermistor assembly.
removed top and front. heater is at the base of the tub. the nut compresses the rubber seal and may take some wiggling to remove the old one.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gregory from PITTSBURGH, PA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Drain pump inoperable
1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- lawrence from DOBBS FERRY, NY
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Water wouldn't drain
I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Timothy from SCOTTSBORO, AL
- Parts Used:
- ACA56078801
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers
Instructions on how to turn Clamp counter clockwise to get back on tube assembly
Watched videos but didn’t show the clamp had to be placed on counterclockwise
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- christen from HUMBLE, TX
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Wrench (Adjustable)
The hot water valve was leaking
It went great. First of all, thank you Part Select for the video on how to do this myself. My home warranty company was giving me a hard time. Blah, blah, blah. A mechanic friend of mine referred me to this site. Within minutes I found the part I need and a GREAT!!!! price. Ordered it, got it super fast, fixed it my self and my second hand washer is no longer peeing all over the floor. Very very happy. I will definitely be a repeat customer, hopefully not anytime soon.
Thank you again for an amazing experience.
Thank you again for an amazing experience.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jesse from CARNEGIE, PA
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver, Pliers
Dishwasher would not fill
Used Youtube to look for a set of repair instructions. From start to end 35 min.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.
Overall very easy to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bobbie Joan from ASHEVILLE, NC
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Door would not close because the part that was in the door that held it closed kept falling out.
Order the part through PartsSelect. It arrived in a few days and I (an 81 year old woman) replaced it within minutes with no help needed. It was super easy.
Was this instruction helpful to you?
Thank you for voting!