GCWF1069QD3 (ASSEELC) LG Washer - Instructions

I BROUGHT UP THE YOUTUBE REPAIR VIDEO AND FOLLOWED IT STEP BY STEP AND WORKED OUT GREAT THANKS

Remove old one and replace. Just make sure it is all the way on and secure or you will have a huge mess on your hands.

Pull the washer away from the wall to get behind it. Unplug the electrical power cord from the wall. I removed the top cover by unscrewing the 2 screws on the back of the washer. Slide the cover back about 1-2 inches towards the back of the washer and then lift the cover up and remove. It might be a little tight to slide back, you may need to wiggle the cover side to side or give it a good smack. The water inlet valve is directly at the top inside of the washer. I saw a slow leak dripping from the hot water inlet valve onto the back side of the drum. Turn off the water supply valve at the wall and then unscrew the supply water hose from the water inlet valve at the back of the washer. Disconnect the electrical connector and water hose from the inlet valve inside the washer. From the outside of the washer on the back, remove the screws holding the water valve and lift out the valve. Install in reverse order.

Some screws, some clamps. Easy and straight forward. unplug machine, turn off water, disconnect water hose, unscrew top of machine (2 philips head screws), disconnect clamp from valve (use a towel for remaining water), disconnect wire, unscrew from place holder, remove entire valve, work backwards from there.

This was very easy to instal. The aplaiance repair co. wanted $240 my LG is six years old and would rather buy a new one if I had to spend that much, so I gave it a shot and it took me 20 min to install the part. Told my wife she owed me $ 180 for my labor.

I watched a video of how to replace the pump and it showed taking the top and front off to get to it. I actually found this could be done by removing the back panel from the washer. There were two hose clamps you have to squeeze and slide up and two wires going to the pump. There are three screws holding the pump that need to be removed from the front of the washer. Once these are removed all you have to do is push a tab down and the motor slide right out. The pump assembly can also be reached from the bottom of the washer.

found the leak, went to the website, called customer service, ordered the part... $24 later, problem solved. Great customer service and on-line support

Simply took hose off from inside machine and replaced it with new one. The tore one had a stopper on one end that wrapped to front machine; inside filter compartment. So I put stopper on the other end of new hose and wrapped it to it's holding spot in filter compartment.

The repair went well and your parts are easy to find. This is the second time I have used your services and both times have been great. Your parts are at great prices and your delivery is a lot faster that one would think.
Thank you

Removed lid (top of washer), then ran a cycle in normal to identify the failed component, then noticed the water inlet valve assembly for the hot water was leaking, used my pc and went to website Part Select and found to failed part on the parts break down item, then ordered the part, the part "Valve Assembly Inlet" for the hot water arrived 2-days later, replaced valve in less than 5-minutes, disconnected push on electrical connector, unscrewed the valve assembly inlet and installed the new valve assembly inlet, very easy

After finding you on google it was easy to repair. It saved me $95.00 service charge. Your direction made it very easy.

removed dryer which was stacked on top of dryer. opened washer top by removing screws from plastic hold down parts on rear. replaced valves with new valves you all sent me. reassembled and restacked dryer on washer

I received the part needed within a few days from ordering. I immediately removed the leaking part with the new part. It was a very simple install, and my washer is now leak free. If you think you cannot do these simple changes, think again, it's much easier then you may think. Remove the top cover of your washer machine by taking off the two screws in the back. Remove the hose clamp with a pair of pliers and pull off from the intake valve, of course make sure your water valve is shut off before starting. Remove the two prong clip. Using your pliers, disconnect the main hot water hose. Use a Phillips screwdriver to remove the two screws that holds the valve in place. Remove and discard it and replace with the new valve. Follow the steps and your done, it's that easy....TC

Hardest part was getting the correct part. Due to some glitch somewhere there was a mix up in the database for the correct pump number. This unit has two pumps mounted to the same housing. One is a recirculating pump and one is discharge pump. I ordered the discharge pump and kept receiving the recirculating pump. Discharge pump is LG PART#4681EA2001T and recirculating pump is LG PART #4681EA2002H Once in hand the install went fairly smoothly. Removed top - two screws on back of unit. Removed control panel with one screw on upper right inside corner, associated plugs and snap clips. Removed soap tray and drained water through filter tube. Removed screws in front of filter. Using Vise grips stretched spring from around front seal. Removed screws holding front of washer to top frame (2?)[accessed after soap tray removal]. Pump assembly located in bottom left, removed associated hoses, Marked wired colors on pump housings and removed. Removed assembly. Unscrewed pump, installed new pump and reversed procedure to reassemble. Struggled mostly with replacing spring around front seal. Stretch it as far apart as you can as you "roll" the spring in and then massage the seal to get the spring into correct position. Definitely a doable repair. Good Luck.

Did the repair entirely from the back.- 4 screws back cover comes off. Once you see the Bellows it is obvious what needs to come off and there are other videos on the net showing this. The main things I did differently were 1) Leaned the washer forward and placed 3 2x4 blocks of wood under each back leg. This allowed me to reach under the washer with one hand, and through the back with the other. You need both hands in there ! 2) Uninstalling is easy with just pliers. But on the way back in, I used a pair of Locking Pliers to keep the circular clamp squeezed as much as possible. That seemed the only way to get the bellows back in. Another option would be to switch to screw on Pipe clamps instead of the spring clamps.