WM3575CW (ABWEPUS) LG Washer - Instructions

you tube it , not to hard to install

Super straightforward to diagnose and repair.

There was puddle under the washer.

I removed the top (screws in rear, slide top toward rear slightly and lift) and followed the trail of water up to the top washer hose between the drum and detergent tray.

Two hose clamps to remove and replace, then replace the top and ready to go.

Figured out how to take off top of washer, look inside for problem, ordered new part, watched video how to replace part. All on line. $65.00 later and my 19 yr old washer is still working awesome.

2 hose clamps and a hose, easy! This would be a very common cause of leaks in washers due to all the movement inside.

YouTube is your friend for many such repairs. See this link for an overall description:

https://www.youtube.com/watch?v=WuvLuC8x4_s

I had to remove the top panel to determine exactly which valve was leaking. It turned out both hot and cold-water valves were defective.

After unit is unplugged and top is removed, it's a simple matter to remove/replace hose connections and electrical connections. It took me less than an hour to complete the task once parts were in hand.

Again, YouTube is your friend for such repairs.

Removed items step by step in sequence as per video to get to baskets . Knocked out bearings and gasket seal. Replaced new parts and in reverse reassembled as per video. Very difficult without video to follow. My bearings were easy to remove but some are frozen in so will need oil ,bars or pipe to fit opening to drive out old bearings. Use camera and notes of sequence to aid in reinstall. Separate and mark fasteners as removed. Note : Was initially told by appl Insurance service person my bearings were bad because when attempting to spin a noise was heard and this not covered by plan ,but I found the motor position sensor had failed by testing it with multimeter which is a low priced part and easily accessable from back. Water hose screens partially clogged also. Canceled Appl service contract.

Unplug and disconnect water lines. Move washer out. I used soapy water to make it easier to slide because it is stacked washer and dryer. Slid dryer onto large trash can saving my back. So easy. Make sure it is heavy duty . Removed lid. Removed old part by removing to screws in back. Disconnected 3 wires, disconnected one hose at a time while reattaching each one to new part. That way I was sure to get them back in the right place. Attached back to machine . Put water hoses back on and checked for leaks before but lid and dryer back in place. Ta da!! This was so easy. I am a 57 year old woman and this was pretty simple. I tried trouble shooting by using tub cleaner and everything as manual suggested but it still leaked. Watch a lot of you tube. Apparently lg has this happen with this part a lot. Thank you parts select. I’m sure this saved me a lot of money. I have had enough money bleeding from my pockets with bigger home problems. Thank you.

I actually did the repair exactly as the video showed. If I would have had the part at the time of discovering the problem it would have been about a 45 minute repair from start to finish. Worst part of the whole fix was moving the heavy washer.

We replaced the three dampers, two in the front and one in the back. We referred to the YouTube video someone posted on this page.

I followed the video. Everything worked exactly as described. i ran a quick cycle and everything seemed to be fine. Started a wash and the machine was going fine but stopped, and wouldn't drain. I thought that maybe it might be the Rotor Position Sensor assembly, which I had already purchased just in case.But first i drained the machine and checked out the pump filter. Plugged solid. I'm guessing when the pump went there must have been a lot of lint and debris in the machine. something you might want to check out, after that repair. Thanks. you guys saved me a couple of hundred dollars

I ordered the Rotor Assembly and Sensor Assy..
Rotor Assy. was not the problem.
1 - 17mm bolt in the center of the rotor assy.
6 10mm bolts to take off the Stator assy.
once you have the Stator assy off, upplug the sensor assy and release the clips on the sensor assy. and remove.
Install the new sensor assy. and plug the electrical connection back in.
replace the 6 bolts and screw the bolts evenly around the Stator.
replace the Rotor Assy. and secure the 17mm bolt.
Replace the back cover (4 - philips screws.
Do a test load.

Unpluged -shut off water removed 2 screws on lid,removed lid took 2 screws out holding part on swapped the hoses out and pluged wires in.

1 tilt washer back
2 remove cover plate screw from front of drain filter access panel.
3 Remove cover plate and remove 2 more mounting screws .
4 go below washer and pull down sliding clip and move pump assembly back.
5 remove wires and 3 mounting screws around pump housing
6 Swap pump and re-attch wires

followed video exactly and it worked perfectly

Used Youtube to look for a set of repair instructions. From start to end 35 min.

The difficult part was getting the door back on. Only 1 Youtube video I watched stated Do not remove the 2 center screws at the top. Wish I had seen that video first.

Overall very easy to do.