WT1201CV ((ASSEECI)) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Sharron from RICHMOND, TX
- Parts Used:
- AEN73131406
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Socket set, Wrench set
I had no problems
I can’t really say it was easy and I just did it
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Richard from DICKSON CITY, PA
- Parts Used:
- 6322FR2046G
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
Washing machine was displaying te code. Quick google search to diagnose the issue.
Very simple repair after watching YouTube video on how to complete repair.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- David from BOTHELL, WA
- Parts Used:
- AEN73131406
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
washer making noise when washing. rinse and spin was normal.
Everthing went to plan except the wet side of the parts removal was difficult. used puller to remove the wash plate and got it to release. But the plastic part of the wash plate released and left the aluminum part still on the coupling. Corrision was the problem, and I had to again use a puller to remove this part of the wash plate. So it wasn't a matter of just lifting the wash plate off by hand. The rest of the replacement was fine.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from FT WORTH, TX
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Pulsator stripped out
The teeth in the pulsator assembly where stripped out on the original plate.
Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair
Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from THOMASTON, GA
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
could not get the 10 mm nut to loosen
Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from ORLANDO, FL
- Parts Used:
- ACP72929002, MCJ61861201
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Wrench (Adjustable)
Washer made a clicking sound during agitation
Move the washer to the garage and laid it on its side. Remove the large nut from the center shaft using a crescent wrench. Tap the wrench with a hammer until the nut comes loose. Next you'll need a puller to remove the part that was secured by the nut. Mine would not come off by hand. Next remove the three screws securing the white plastic components to the bottom of the washer. Remove the two plastic pieces and throw them in the trash because I'm sure they're garbage. Reverse the process for installation and reinstall the washer. Put some clothes in for the test wash and the washer should be silent. Two different appliance repair folks gave me estimates that were higher than the cost of replacement. I got out from under this fix for around a hundred bucks. It was worth every minute of my time. Good luck.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from EDWARDS, IL
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
very dirty under adjitator cap and pulsator
Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristen from Safford, AZ
- Parts Used:
- AGZ72909711, 5006EA3009B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Washer pulsator was coming loose during wash cycle.
Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.
Was this instruction helpful to you?
Thank you for voting!