WM3250HWA (ABWEEUS) LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Keith from ROCKAWAY, NJ
- Parts Used:
- 5220FR2075L, AGM73269501, 5220FR2006H
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Screw drivers, Socket set, Wrench (Adjustable)
Water was leaking into washing machine after the washer was shut off
Removed the cover from the washing machine, the two valves(cold & hot) are located in the read top of the machine, removed the hoses to the valves, removed the nut that holds on the valve to the washer and placed new valve into washer and placed the nut back onto new valve, placed the hoses back onto the new valve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Terry G from FORT WORTH, TX
- Parts Used:
- 383EER3001J
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Excessive vibration
I followed the video -- to take apart and reversed the steps to re-install. It was fairly straight forward and corrected the issue.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Gerald from CENTRALIA, KS
- Parts Used:
- MAP61913707, 4280EN4001C, 4036ER4001B, 4036ER2004A
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Pliers, Screw drivers, Socket set
Very noisy when tub was spinning , tub bearings and seal were bad.
Watched a YouTube video on how to disassemble the washer step by step, replace the bearings, and reassemble the machine. was very helpful.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ray from RIO RANCHO, NM
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Screw drivers, Socket set
Washer not pumping out and making ominous noises
Totally dis-assembled this washer to check the bearings and drum plus fix the pump problem. We wash dog blankets occasionally and found the little drain hose from the front door gasket was clogged with hair. It makes a 90 degree turn and it gets caught there. THAT fixed the smell issue. As far as the pump replacement goes its quite easy. Videos online are your friend.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marshall from ROSEVILLE, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Noisy and drum still full of water . Will not go to next cycle.
Follow the LG washer video.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ROBERT from BETHLEHEM, GA
- Parts Used:
- MAP61913707, 4036ER4001B, 4036ER2004A
- Difficulty Level:
- Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Pliers, Screw drivers, Socket set, Wrench set
Dry bearing noise
I researched the symptom, watched a repair video, ordered the parts: one rear bearing, seal, and gasket. After disassembly found inner bearing to be bad. Ordered inner bearing. Then found the spider or hub shaft corroded, and ordered spider. Finally with all the parts replaced, assembled washer and returned it to service.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Lonnie from JACKSONVILLE, FL
- Parts Used:
- MAP61913707, 4280EN4001C, AFC72755401, 4036ER2004A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- More than 2 hours
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Very nosey
Replace both bearings and seal also replace spider gear due to the bearing seal surface damage,also replace drum gasket and door gasket and all shock absorber.The clean up two more time then the repairs did.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeffery from NORTHFIELD, IL
- Parts Used:
- 5220FR2075L, 5220FR2006H
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Water was collecting in the machine after it finished its cycle.
Turned off hot and cold water supply. Pulled out machine and disconnected hoses, unplugged power.
Unscrewed 4 screws at back top of machine (holding plastic bracket to cover). Pulled out trays from front where detergent is poured, and removed small screws under trays.
Slid cover back and up. This was the only tricky part. There are pegs that must line up with large holes in cover before you can easily lift cover up. Helps to look from underneath and find pegs on each side.
Using pliers, fully open clamps holding hoses to the inlet valves, and carefully pull off hoses while keeping clamps open with pliers… making sure to keep track of which hose goes to each motor. Take a picture of electrical connectors noting color and sequence of connectors on each inlet valve motor. Pull all connectors off.
Unscrew screws holding each inlet valve to machine. Put new inlet valves in place of old, and screw in place. Reconnect hoses (using pliers to hold open clamps, then slide clamps over tubing and inlet valve connector). Reconnect electrical connectors carefulljng lining up colors of wires and sequence using picture taken in previous step.
Replace cover. Screw all screws back to secure cover. Replace trays.
Unscrewed 4 screws at back top of machine (holding plastic bracket to cover). Pulled out trays from front where detergent is poured, and removed small screws under trays.
Slid cover back and up. This was the only tricky part. There are pegs that must line up with large holes in cover before you can easily lift cover up. Helps to look from underneath and find pegs on each side.
Using pliers, fully open clamps holding hoses to the inlet valves, and carefully pull off hoses while keeping clamps open with pliers… making sure to keep track of which hose goes to each motor. Take a picture of electrical connectors noting color and sequence of connectors on each inlet valve motor. Pull all connectors off.
Unscrew screws holding each inlet valve to machine. Put new inlet valves in place of old, and screw in place. Reconnect hoses (using pliers to hold open clamps, then slide clamps over tubing and inlet valve connector). Reconnect electrical connectors carefulljng lining up colors of wires and sequence using picture taken in previous step.
Replace cover. Screw all screws back to secure cover. Replace trays.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- SHIRLEY from HARTFORD CITY, IN
- Parts Used:
- AGM73610701
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
Magnetic Door Plunger would stay on washer and not stay in door.
Use just your finger to push it into place. VERY EASY
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Sandra from Livonia, MI
- Parts Used:
- 383EER2001A
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
The pump filter leaked after cleaning it out. Would work with teflon tape, but wanted to see if a new part would eliminate the need to wrap it every time.
Unscrewed the old part; screwed in the new part and said a quick prayer - LOL!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!
The part worked great, but I wanted to mention how quickly I received the part!
I would definitely order from this company again!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kevin from WASHINGTON, DC
- Parts Used:
- 5220FR2006H
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Screw drivers
w/d repeatedly fills with water during warm or hot loads
E. Z. hardest part (which isn't hard) was moving the appliance to reach the back, then putting the appliance back into place. the actual repair (swapping out valve) took less time than that to do.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Millie from MANORVILLE, NY
- Parts Used:
- 5220FR2075L
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Wrench (Adjustable)
Bleach dispenser not emptying.
First unplug the machine. Turn the water off to the hoses. Remove the hoses from the machine to make it easier. Remove the screws from the back of the top cover. Pry the front sides with a screwdriver and lift. Standing behind the machine on the left side you’ll see the three solenoids or inlet assembly. Remove the two screws so as to take the inlet assembly out. There are hoses attached to the assembly.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Ignatius from PARKERSBURG, WV
- Parts Used:
- 5220FR2075L, 383EER3001J
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Cold water inlet was leaking. The back Shock Absorber was a little rusty from the water.
The repairs went great thanks to the videos and Steve.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kenneth from CONESUS, NY
- Parts Used:
- 383EER3001J
- Difficulty Level:
- Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers, Socket set
Washer shook in spin cycle
Took front of machine off to access 2 shocks, put back together then removed panel in back to access third shock, watched YouTube video first so things went smooth
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jo Ann from WYLIE, TX
- Parts Used:
- AGM73610701
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
Plunger/magnet capsule fell out of door recepticale because plastic locking tab broke off
Simply inserted new plunger/magnet back into door with thumb&finger until you hear the little locking tabs click. No tools required.
Was this instruction helpful to you?
Thank you for voting!