Models > WT1301CW

WT1301CW (ABWEVUS) LG Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".

Diagrams for WT1301CW

Viewing 3 of 3
Keep searches simple, eg. "belt" or "pump".
This is an authentic LG water inlet valve for a top-load washer. It is designed to control the flow of water into the washer. If your washer is filling slowly, making loud noises, overflowing, or stop...
In Stock
Order now and your part arrives by Nov 23
Clothing moves over a covered mounting point with help from this washer pulsator cap. The round plastic cover snaps into the center of the washplate, concealing the mounting bolt and providing a smoot...
In Stock
Order now and your part arrives by Nov 23
Drain used wash water with this top-load washer drain pump assembly. Its motor drives an internal impeller that pushes water from the tub through the drain hose during drain and spin cycles. This is a...
In Stock
Order now and your part arrives by Nov 23
This washer tub-to-pump drain hose is used to carry used water from the outer tub to the drain pump during draining. Its flexible, corrugated design accommodates tub movement while keeping water conta...
In Stock
Order now and your part arrives by Nov 23
Smooth lid movement starts with a secure pivot point, and this washer top lid hinge connects the lid to the top panel. It supports the lid during opening and closing, helping it stay aligned with the ...
In Stock
Order now and your part arrives by Nov 23
$32.95
Restore a washer component?s fastening point with this replacement screw when the original is missing, stripped, or damaged. Secure fastening helps parts stay firmly attached during operation. A worn ...
In Stock
Order now and your part arrives by Nov 23
This pressure sensor assembly measures changes in air pressure through a connected tube as water enters or leaves the tub. Accurate water level sensing helps the washer fill and advance through its cy...
In Stock
Order now and your part arrives by Nov 23
This clutch housing assembly with mode shifter, or washer drive shaft and shifter assembly, is made for your washer. It connects the appliance wash plate to the motor so the washer can shift the drive...
In Stock
Order now and your part arrives by Nov 23
In Stock
Order now and your part arrives by Nov 23
On Order
In Stock
Order now and your part arrives by Nov 23
In Stock
Order now and your part arrives by Nov 23

Common Problems and Symptoms for WT1301CW

Viewing 10 of 10
Leaking
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Will not drain
Fixed by these parts
Fixing
How to fix it
Water Filling Issues
Fixed by these parts
Fixing Fixing
How to fix it
Will not agitate
Fixed by these parts
Fixing Fixing Fixing
How to fix it
Lid or door won’t close
Fixed by these parts
Fixing
How to fix it
No hot or cold water
Fixed by these parts
Fixing
How to fix it
Draining Issues
Fixed by these parts
Fixing
How to fix it
Will Not Start
Fixed by these parts
Fixing
How to fix it
Spinning Issues
Fixed by these parts
Fixing
How to fix it
Marks left on clothes
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Jesus from El Paso, TX
Parts Used:
5859EA1004P
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Socket set, Wrench set
It did not drain water, cycle stops at rinse+spin.
1-Take water off manually. 2- Take machine to back yard. 3- lay machine 45 degrees. 4- Located water bump, (rear left side). 5-removed drain black hoses with hand. 6-removed 3 screws from bump frame. 7-Taker off all unit and marked down cable position at plug. 8- installed new pump. 9- Reverse all steps. Note: I did not use new cable su pplied with the new bump, I did not want to mess around on mother board connections, I kept old wire harness which are only two cables blue and gray. It took me less than 30 minutes.
28 of 36 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
John from SAN JOSE, CA
Parts Used:
MEF62462103
Difficulty Level:
Very Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers
The right side hinge that holds the washer top door broke and needed to be replaced.
Popped out the plastic "doors" that cover the metal actuators. Removed the metal actuators on both right and left sides of the door then unscrewed (3 screws each actuator) them from door frame. Slid the actuators out to enable the door to be removed. Unscrewed 2 screws on the top front of the washer which enabled me to angle the top of the washer to expose the screws that hold the plastic hinges. Unscrewed the hinges (2 screws each) and replaced both of the hinges (I figured I'd do both of them now so I don't have to do it again for another 15 years). Put everything back together and all works like new.
18 of 20 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Flora from MIAMI, FL
Parts Used:
AJU75152601
Difficulty Level:
Very Easy
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers, Wrench (Adjustable)
Water continued leaking into washer after the end of cycle through the water inlet valve.
Did the repair Myself. Saved $ 400.00 in the process.
14 of 19 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!