WM3575CV LG Washer - Instructions

followed video exactly and it worked perfectly

Took off top of washer to get access to connector nozzle, which is on top front of washer rubber boot. removed old nozzle, installed new one. Easy peasy

I already had the top of the washer open, from previous disassembly to clean the front loader seal, and when I ran a trial load, noticed a small 1/4" tear in the hose bellows that attaches to the drum.

Very simple repair, remove the existing hose by loosening the clamps, paying attention to their orientation. Install the existing hose clamps onto the new hose, install and tighten the hose clamps.

5 minute job, if the washer top is off (which is also simple).

…and was not able to get this part for three weeks
PartSelect had it in stock and delivered within one day of ordering.
The next technician said it did not need this part and went ahead and fixed the washer.
However, your fast service and easy return were outstanding.
Thank you very much I can recommend you highly!

1. Unplugged electric chord from wall.
2. Pulled washer out into open area to get behind it.
3. Turned off hot and cold water faucets
4. Used channel locks to remove hot water and cold water hoses from back of washer. Dropping hose into a bucket to catch water from hose.
5. Removed screws (Phillips screw driver) holding top to back of washer.
6. Pulled back on the top and lifted off washer.
7. Arranged new intake valve to mock location and setting of old intake valve.
8. Using Phillip screw driver, unscrewed old intake valve from back of washer.
9. Unconnected wiring from old intake valve. These were easily identified and not needed to mark left right center.
10. Using pliers, pinched hose clips and moved to middle of the hose. Did this for all 3 hoses.
11. Removed hose from old intake and connected to same location on new intake. Repeated for all 3 hoses.
12. Using pliers, pinched the clips and moved to the end of the new intake valve. Did the for all 3 hoses.
13. Using Phillips screw driver, screwed in the new intake valve where the old intake valve was located.
15. Inserted the wiring connects into new intake valve.
16. Reconnected water hoses back into washer machine (after inspecting and cleaning plastic strainer traps)
17. Turned on water faucets
18. Plugged in washer.
19. Ran an empty load for a cycle.
20. Did not fail.
21. Reattached top to washer. Laying down an inch from front and push forward to hear a click or lock. Then screwed in the 2 screws.
22. Pushed washer back into original location.

We have already performed 1/2 dozen loads.

just put new part in very simple only problem was shipping yall used fedex went to 4 states and one state twice they finally gave it to USPS so it took almost 9 days to get here

Ordered and replaced the hot and cold inlet valves - followed the instructions off of the video posted on the Part Select website ... completed the repair in less than 10 minutes

Replaced it

To fix the problem, I simply removed the top cover of the washing machine by removing the two screws on the back of the machine which allowed me to slide the top back and then I lifted it off. Then I disconnected the hot water hose (after shutting off the valve). Next, I removed the electrical connectors on the old part as well as the hose attached to it and unscrewed the old part and removed it and put the new one on and reattached the hoses and the electrical. It worked like a charm. It took me perhaps 10 minutes total.

Found this part online. I just sets inside, did not click in like the bleach and fabric softener inserts. Think is ok, seems to work

All I did was first of all and since it is so heavy I put 2 furniture sliders under the 2 front feat because I had to pull it out from where it was onto the carpet and the back feat I just sprayed some wd40 so the would slide on the tile floor. Then I took the top off by removing 2 bottom screws and pulled the lid back and up and there was the cold valve. Next I pulled the electric tabs off. Don’t worry they go on the same way they were on. Do not at this time remove the screws on the valve until you pull each off one at a time and place one at a time back on the new valve. Then remove the screws and the old valve and put the screws back on for new valve and you are done. Replace cold water hose turn on water check if no leaks replace lid, you are as if new once again. Good luck. Cost for all that is around $50

Took off the old hose with a screwdriver and put the new one on. As simple as that. You don’t need a repair man to get this done, you can do it yourself and save money too.

Looked at videos on line at Parts Select. Very easy instructions to watch and follow. After unplugging the washer all I had to do was turn off the cold water valve, remove the supply line, two screws to get the lid off, then two screws to remove the valve and disconnected the electric connector tabs. Took pliers to back the three hose clamps off. The best tip was replacing each hose back on the valve one at a time to prevent mix ups. I did everything in reverse after installation. I ran one short cycle to test the leak. Works perfectly!
A tip I saw on You Tube - I have vinyl flooring in my wash room and a repair guy said to spray a light shot of WD 40 under the feet. It doesn’t take much. Man, my washer slid like it was on wheels! I wiped away any excess spray and let it dry under the feet. I’m not sure how this works on other types of floors.

I followed the video and it was quite simple. There was an extra sheet metal screw at the bottom of the front panel which kept it from coming free of the three tabs. On the two pump wite connectors I made a mental note that the black wires were on top. The repair also fixed the lack of water flow through the degeterent dispenser. I was afraid of putting the tub seal back in place as a pro struggled with it when it was new and under warranty. It really was no problem at all. Take some phone pics along the way boosted my confidence.

Watched video on U-Tube , unplug power cord, turn off water, take top off washing machine, remove water hoses, unscrew parts, remove hoses with pliers, install replacement parts, put all back together. Does not leak any more !