T1475HGPV LG Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Joel from JASPER, MO
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Nutdriver, Screw drivers
Agitator was free spinning
Removed the center cover cap carefully on top of the agitator with a small screw driver. There are 3 (on mine) little slots around the edge of the bottom of the cap where it meets the agitator. Insert the small flat blade screwdriver and gently twist at each one till the cap pops loose and comes off.
There was a 10MM bolt under the cap on mine that you need to remove. I used an cordless impact driver but you could use a socket wrench as well. Remove the bolt and the agitator comes off. May take a little wiggling or it may come right off.
The teeth on the agitator were wore all the way down and gone on mine so it came off easy and this was the issue I had why it was spinning freely. I took the small flat blade screwdriver and used the edge and corner of the blade to clean the teeth on the shaft where the agitator attaches and wiped it down before installing the new part as there was quite a bit of metal shavings from the damaged part.
I just reversed the order of removal to install the new part. Took about 15 min. I ran a rinse and spin cycle to remove any additional metal shavings and to check to see if it all worked properly. THATS IT! TOO EASY!
There was a 10MM bolt under the cap on mine that you need to remove. I used an cordless impact driver but you could use a socket wrench as well. Remove the bolt and the agitator comes off. May take a little wiggling or it may come right off.
The teeth on the agitator were wore all the way down and gone on mine so it came off easy and this was the issue I had why it was spinning freely. I took the small flat blade screwdriver and used the edge and corner of the blade to clean the teeth on the shaft where the agitator attaches and wiped it down before installing the new part as there was quite a bit of metal shavings from the damaged part.
I just reversed the order of removal to install the new part. Took about 15 min. I ran a rinse and spin cycle to remove any additional metal shavings and to check to see if it all worked properly. THATS IT! TOO EASY!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Deresa from BOLINGBROOK, IL
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
The bolt in pulsator kept coming out during the wash
I found the pulsator just spun freely, I determined the hole on underside should ribbed to align with the ribbed shaft. But it was wore away. I purchased the new part and replacement was simple. It slide right on and I replaced the bolt. Pulsator works great, washing again.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Anthony from FT WORTH, TX
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Pulsator stripped out
The teeth in the pulsator assembly where stripped out on the original plate.
Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair
Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Daniel from EDWARDS, IL
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Wrench set
very dirty under adjitator cap and pulsator
Tried to remove adjitator but it was stuck. Could not find any professional method of pulling it. There must be some type of puller,
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Kristen from Safford, AZ
- Parts Used:
- AGZ72909711, 5006EA3009B
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Washer pulsator was coming loose during wash cycle.
Since the old pulsator had actually come off during a wash cycle, I was able to place the new one on easily. Tightened the screw with a socket. Then placed the new cap on. Before placing the new pulsator on, I was able to clean all the mold and hard deposits off the mechanism under the pulsator. The hard deposits were also scrapped from the pulsator holding (where the screw goes) which may have caused the problem to begin with.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Marilyn from THOMASTON, GA
- Parts Used:
- AGZ72909711
- Difficulty Level:
- Very Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Nutdriver
could not get the 10 mm nut to loosen
Tried everything and could not get it out I just use mesh bags for washing at this time, but LG washing machine is the worst I have ever had
Was this instruction helpful to you?
Thank you for voting!