Models > T1475HGPV

T1475HGPV LG Washer

Jump to:

Find Part by Name

Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
PULSATOR ASSEMBLY – Part Number: AGZ72909711
$179.18
In Stock
Pulsator Cap – Part Number: 5006EA3009B
$30.01
This part is known as a pulsator cap or washplate cap, and is designed for your LG washer. It fits over the washplate mounting bolt and prevents clothes from getting caught on the washplate during a w...
In Stock
Tub-to-Pump Hose – Part Number: AEM73213001
$32.17
In Stock
Switch Assembly,Sensor – Part Number: 6501EA1001R
$49.27
In Stock
Door Lock Switch – Part Number: EBF61215204
$171.60
In Stock
Motor Assembly Clutch – Part Number: 4681EA1009C
$104.55
In Stock

Questions and Answers

Be the first to ask our experts a question about this part!

Common Problems and Symptoms for T1475HGPV

Viewing 2 of 2
Will not agitate
Fixed by these parts
Fixing Fixing
How to fix it
Leaking
Fixed by these parts
Fixing
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
Customer:
Paul from NANTICOKE, PA
Parts Used:
AGZ72909711
Difficulty Level:
Really Easy
Total Repair Time:
1- 2 hours
Tools:
Socket set, Wrench (Adjustable)
Washer was noisy, made noise when agitating and spinning.
I had a hard time removing the agitator, had to get thin prybar to get a hold of washplate. After I removed washplate, I found that the shaft that the washplate attaches to was actually worn out. What used to be a spline was smooth. So I ordered a new clutch assembly. There are a lot of bolts that hold the clutch assembly on to the basket. There are a lot of videos on Utube that will walk you through step by step. The only problem I encountered with this was removing the nut that holds the basket to the tub. One video said it was reverse thread, which it wasn’t. You can check the thread on new clutch assembly to see which way is correct. After I put back together. Works like new.
Read less
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Joel from JASPER, MO
Parts Used:
AGZ72909711
Difficulty Level:
Very Easy
Total Repair Time:
Less than 15 mins
Tools:
Nutdriver, Screw drivers
Agitator was free spinning
Removed the center cover cap carefully on top of the agitator with a small screw driver. There are 3 (on mine) little slots around the edge of the bottom of the cap where it meets the agitator. Insert the small flat blade screwdriver and gently twist at each one till the cap pops loose and comes off.

There was a 10MM bolt under the cap on mine that you need to remove. I used an cordless impact driver but you could use a socket wrench as well. Remove the bolt and the agitator comes off. May take a little wiggling or it may come right off.

The teeth on the agitator were wore all the way down and gone on mine so it came off easy and this was the issue I had why it was spinning freely. I took the small flat blade screwdriver and used the edge and corner of the blade to clean the teeth on the shaft where the agitator attaches and wiped it down before installing the new part as there was quite a bit of metal shavings from the damaged part.

I just reversed the order of removal to install the new part. Took about 15 min. I ran a rinse and spin cycle to remove any additional metal shavings and to check to see if it all worked properly. THATS IT! TOO EASY!
Read less
5 of 9 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
Customer:
Anthony from FT WORTH, TX
Parts Used:
AGZ72909711
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers, Socket set
Pulsator stripped out
The teeth in the pulsator assembly where stripped out on the original plate.

Ordered the replacement and it was 1 screw to undo and pop in the new assembly. Super easy repair
2 of 4 people found this instruction helpful.
Was this instruction helpful to you?
Thank you for voting!
View More