Models
>
WD-10580BD
WD-10580BD LG Washer
Jump to:
Find Part by Name
Keep searches simple, eg. "belt" or "pump".
Keep searches simple, eg. "belt" or "pump".
$59.43
This is a drain pump motor assembly for washers. This OEM part is responsible for removing water from the washer during the drain part of the cycle. When this part is clogged, damaged or defective it ...
In Stock
Order now and your part arrives by May 3
$36.42
The hot water valve is found at the back of your washer and controls the flow of hot water into the machine. If the valve is defective, the washer may leak, overfill, fill slowly, or not fill with wat...
In Stock
Order now and your part arrives by May 3
$25.10
This replacement pump filter, also known as a filter assembly, is a genuine OEM part for your washer or washer/dryer combo. Before beginning this repair, turn off the power and water supply to your wa...
In Stock
Order now and your part arrives by May 3
$21.82
The locking pin is used to hold the shock absorber on the washer. There is a pin used at the bottom and top of the shock absorber. Sold individually.
Special Order
$37.49
This genuine OEM drum seal gasket prevents water from leaking between the outer tub and spin basket of your washer. It is made of black rubber and measures 2.5 inches in diameter. If your washer is le...
In Stock
Order now and your part arrives by May 3
$232.16
The spider, or rear tub support, is located behind the outer tub of your washer, and provides support to the outer tub. It has 3 legs and each measures approximately 10 inches long. If your washer mov...
Special Order
Special Order
In Stock
Order now and your part arrives by May 3
In Stock
Order now and your part arrives by May 3
$57.30
This dispenser assembly holds and dispenses detergent and fabric softener during the wash cycle. Replace it if your current part is clogged, leaking, or damaged. Verify your washer model for proper fit before installing.
In Stock
Order now and your part arrives by May 3
$29.98
This clamp assembly secures hoses, boots, or fittings in place to prevent leaks and maintain proper connections. Designed for a tight, reliable hold, it is replaced when clamps loosen, corrode, or fail.
In Stock
Order now and your part arrives by May 3
In Stock
Order now and your part arrives by May 3
Common Problems and Symptoms for WD-10580BD
Viewing 11 of 11Will not drain
Fixed by these parts
How to fix it
Leaking
Fixed by these parts
How to fix it
Draining Issues
Fixed by these parts
How to fix it
Water Filling Issues
Fixed by these parts
How to fix it
Engine runs but does not pump water
Fixed by these parts
How to fix it
Will Not Start
Fixed by these parts
How to fix it
No hot or cold water
Fixed by these parts
How to fix it
Burning smell
Fixed by these parts
How to fix it
Does not dispense fabric softener or detergent
Fixed by these parts
How to fix it
Noisy
Fixed by these parts
How to fix it
Not draining
Fixed by these parts
How to fix it
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- Jorge from Apple Valley, CA
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Easy
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers
Washing maching wouldn't drain
Removed the top of the washer by removing the 4 back screws and 2 small brackets. Then I removed the front panel, this was actually the hardest part, 2 screws and 8 tabs that you pop out carefully from the top of the panel. I only disconnected the power button and was able to rest the panel on top of the washer. The rest of the washer cam
... Read more
e apart quickly just moving down the front of the washer and removing the door, latch, tub gasket, drain cover. Removing the pump was just a mater of disconnecting the drain hoses, and one clip under the drain assembly. 3 screws attach the drain to assembly to the pump and only 2 wires that are clearly marked. Reassembly is just going back through in reverse order of disassenbly. The best thing about this is that it all comes apart with a standard phillips screwdriver.
Read less
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Michael from RALEIGH, NC
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
noisy operation, sometimes did not drain, gave OE code
Thank you for the very helpful YouTube video. After watching the video, I was able to diagnose the problem, buy the part from your website, and complete the repair. This is my personal machine - I am not a professional repairman.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Bill from COTTAGE GROVE, WI
- Parts Used:
- 4681EA2001T
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 30 - 60 mins
- Tools:
- Pliers, Screw drivers
Pump rotor broke off shaft.
There are two pumps in this system. I turned the washer on its side and took off bottom plate. There are several screws holding this on. I then took the entire pump assembly off. There are 3 screws holding each pump on the brown plastic body. Each pump has a positive and negative lead. I switched out the pump and reassembled. The h
... Read more
ardest part is getting the 3 "shock absorbers in place with the rubber sleeves. I think the book suggest getting to the pump from the front side but I went through the bottom. Worked good. I did wonder however if the other pump was working. Do you need two pump working to get flow? By replacing one pump I went from no flow to good flow. Cost me $75.00
Read less
Was this instruction helpful to you?
Thank you for voting!