KAWS700LQ0 KitchenAid Washer - Instructions
Jump to:
Keep searches simple. Use keywords, e.g. "leaking", "pump", "broken" or "fit".
- Customer:
- eugene from sussex, NJ
- Parts Used:
- 285753A
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers
No drive from motor
Watched the video and it was very straight forward, very easy and time saving. I just wish the delivery time for the part was that fast (It was a quick delivery).
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Mary Jane from Plymouth, MI
- Parts Used:
- 285664
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Pliers
Worn, leaking drain hose
It was a no-brainer repair. We removed the worn hose and replaced it with the new one. Only variable was that the new clamp was too big for our fitting, so we used the old one. The clamp was the only mechanical thing we did. The best part was the very prompt delivery of the new part and the help finding it from the rep at the company.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- William from Midland, MI
- Parts Used:
- WPW10074580, 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Pliers, Socket set
Upper part of agitator was able to move freely both ways
I had already taken the agitator apart to see what the problem might be. that was very simple. When I watched the video you have on your sight, you took it apart the same way I did, so you have it right!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Wendi from Rothschild, WI
- Parts Used:
- 80040
- Difficulty Level:
- A Bit Difficult
- Total Repair Time:
- 1- 2 hours
- Tools:
- Screw drivers, Socket set
would not agitate
repair went well. video presentation was helpful but our washer was not quite the same as video. we had to print the assembly diagram to visualize the proper order to place the new parts. all in all it was a simple fix.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Jeff from Kingman, AZ
- Parts Used:
- 285811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Socket set
Agitator would not agitate
Unbolted the center agitator part then replaced with agitator repair kit, easy breezy japanesee!
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Cliff from Humble, TX
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Screw drivers, Socket set
Agitator not turning
Pop cap off top of agitator. remove bolt that holds down agitator,which lets you remove the top of agitator that holds the directional cogs. remove top install cogs, make sure they are turned in right direction, and re install top of agitator.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Joseph from Lakeland, FL
- Parts Used:
- 285811
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Washer not agitating
Pulled cap off agitator,pulled plug out of inside of agitator, use socket to remove bolt,gently pulled agitator out installed new agitator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- ronald from Plymouth, MA
- Parts Used:
- 80040
- Difficulty Level:
- Really Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
directional portion of agitator didn't turn
as in video
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- kerry from madisonville, LA
- Parts Used:
- 80040
- Difficulty Level:
- Easy
- Total Repair Time:
- Less than 15 mins
- Tools:
- Socket set
Agitator stopped working
After about 4-5 years, the agitator cogs or "dogs" will wear out and cause the agitator to stop working-Simply pop the cap off of the top of the agitator with your hands by pulling upwards, remove the plastic cap at the bottom of the agitator-there are 2 plastic ears that you pull up on also with your hand, exposing a 1/2 locking nut. Use a socket and extention to unscrew the nut. Grab the bottom of the agitator with both hands and pull sharply upwards removing the entire assembly. Flip the assembly over to expose the four cogs. Replace with new, and reverse the procedure to reinstall the agitator
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- James G from Crossville, TN
- Parts Used:
- 285785
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Pliers, Screw drivers, Socket set
Would not spin during spin cycle.
After watching the repair video by partselect.com I followed the directions exactly. It turned out to be a piece of cake. I found out that partselect.com has many, many do it your self repair videos on youtube.com. I intend to use them for future repairs. Thank you partselect.com.
Was this instruction helpful to you?
Thank you for voting!
- Customer:
- Brian from Spring Hill, TN
- Parts Used:
- 285753A
- Difficulty Level:
- Easy
- Total Repair Time:
- 15 - 30 mins
- Tools:
- Nutdriver, Screw drivers, Socket set
Motor Coupling failed after 20 years!
Determined based on some Internet searches that the part that we needed was the motor coupling; washer would not spin or agitate. Once I figured out how to removed the cover (by the way, one of the guys at an appliance store told me how to do it), and reviewing the video on your website, I removed the two screws and four clips, dropped the motor, inserted the parts and put it back together - all in about 15 or 20 minutes. It was easy and clean and the washer worked again. Hopefully go for another 5-10 years. Thanks.
Was this instruction helpful to you?
Thank you for voting!