7MDKL1501WQ0 Kenmore Washer - Instructions

I ordered a new part based on the exact model number and was sent the wrong part. Fortunately the cam dogs were the same size so I was able to re-use the original housing and throw the new one away.

First I removed the fabric softener cup then the cover with seal. I then used an 11mm socket to remove the bolt, pulled up on the agitator cam removed the old gears and replaced with new ones. Put it all back together and it Works great

I decided to order the part and attempt to install it. Actually was easy. Took my time and maybe took 90 minutes. Works great.

Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.

Went on line and ordered the piece I need. I got my socket set out, held the center piece in place then with the socket unscrewed the bolt. Popped the plastic washer off put the agitator clips in, put the plastic washer on and bolted it back together and was done. Easy as 1, 2, and 3.

Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.

I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.

First used wet vac to get water out. Unplug electrical cord. Shut off water and unhook lines. Unhook drain tube. Flip over on side. Take belt cover off. two screws.
Took photos of parts removing just for re- install. Ordered parts from part select.com. Came in Two days. The dealer was on 12 days I gave up on them. I removed actuator two easy screws and pulled off electrical connection no tool needed. Then removed pump three longer screws Than other part. Make sure to label them in a ziplock baggie. Plus I removed hose clamp with pliers slide Back on hose and pull hose off. Then remove electrical connection on pump. If it makes you feel better label each with masking tape so I know where each connection goes. Then replace pump first with new one. Make sure you push it in hard then the screws. Don’t over tighten. Plastic parts break. Hook back up hose slide clamp back over fitting end with pliers. Hook up wire connector. Next hook up actuator. Two screws wire connector and your done. Put belt guard back on. Socks can get caught under washer get in belt and cause major issue. Then you need to reconnect water lines. Make sure hot goes to hot. Cold to cold. Drain hose hook back up. Plug in power cord. Now the fun part. Run a diagnostic and then calibration. See you tube videos it’s like 3 clicks to left then two to right with selector knob. Write down the exact amount of clicks and steps. It works. Be sure to turn knob 4 times to left to clear it like a combination lock. Don’t let the noises scare you it makes all
Kinds of sounds while calibration goes on.

I needed the washer ASAP. I paid extra for the expedited shipping. The parts arrived as promised. I watched the on-line video. I read and followed the included instructions. Removed cap and nut. Pulled out part with "dogs", swapped new dogs and assembly. Re-installed components, I was wary from information gleaned from the video, which warned of proper orientation of "dogs", as they can be inserted backwards. Tightened bolt and re-installed cap. Presto! Repaired washing machine worked as good as new. My coffee didn't even get cold.

Put new one on work good, but now can't pump no more .the problem now is the spin cycal broke and I not going to fix it. Thank for the part work good.

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

Used screw driver to pop top off to access the bolt on spinning unit.Used socket wrench and took bolt off of bottom of spinniner. Replace agitater with new parts and reassembled. Now it works like new.

Popped off agitator cover discovered worn and broken 'dogs'. Decided to replace complete agitator assembly due to age of machine (25 + years). 7/16 socket, removed nut and agitator assembly, installed new assembly with included nut.

Removed softener cup agitator cap and one bolt, lifted agitator out and replaced with new one... tightened bolt replaced cap and softener cup and away we go, done...