11020092991 Kenmore Washer - Instructions

researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.

I decided to order the part and attempt to install it. Actually was easy. Took my time and maybe took 90 minutes. Works great.

Well, after resolving Part Select (PS) shipping issues (PS sent me two refrigerator glass shelves instead of a Tub Spring); And as it turns out they sent me the wrong part for the suspension pads, which I have returned for credit. It takes 3-4 weeks to obtain your credit BTW.

Well after removing the cabinet, agitator, wash basket, plastic tub, all 5 springs, & pump suction line, I was able to access the Tub wear pads and suspension pads. As it turns out the suspension pads looked good.
Thank God, as PS had sent wrong parts. I replaced the wear pads, the 5 springs, and reversed the disassembly process. Took about 6 hours.
But washer works fine now, still vibrates, but does not walk across floor any more.

The tough part was replacing the front cabinet.
I did consult the video for help on replacing the clutch spring.
Thank you for that bit.

I admit to taking too much apart, most of the cabinet back can be left alone.
Some of the plastic wire keepers/routers suffered, as well as the console hinges.

The newly reassembled washer works without a hitch, and truely it took me about 4 hours over several days to dissamble and reassemble.
It is louder in the audible range than before, but very serviceale for another 20 years, saints willing.

Slid off the old and slid on the new part. Actually my wife did it with no help and was rather pleased with her self on not needing any help except ordering it.

Slid the replacement on the lid and it worked like a charm - no more vibration.

Direct drive, no belt. Motor sounds like it's spinning but the agitator is not. Bought the coupling (that goes between the motor and the transmission) and replaced it in less than 15 minutes. Two screws and two clips to open the cover. Two clips to move the water pump out of the way. Two screws and two clips to take out the motor. Replace the coupling and reverse the steps.

Pulled hoses off, unclipped the remaining retainer clip, slid old pump off. Slid new pump on replaced the old retainer clip and put the new one on, replaced the 2 hoses, done. It took mabey 10 min.
The part got there in less that 24 hours from the time I placed the order, with standard shipping! I was impressed.

The video that was shown about how to perform the repair was spot on. I wasn't sure exactly what part I needed. I took the advise from you stating that these symptoms I described usually meant that the part I ordered was the correct repair In 65% of the cases. I was delighted to see that when I followed the instruction video, and the motor was removed, there was my coupling, In several pieces. At that point I knew that I ordered the correct parts.
Thank You,
Mario for Eastchester, NY.

Removed the outside body of washer. Used 1/2 plywood between drum and wear pads to make space to pry out pads with screwdriver. Replaced suspension springs and tub spring (use waterproof grease on end of springs. Put washer back together and tested. Problem solved washer not walking all over floor anymore. Thanks for you help.

Removed the old hoses and screwed on the new hoses.

First I screamed at the ceiling, because I have a three year old and an infant, and the washing machine was dead. Then I went to youtube. It seemed like the "agitator dogs" were the issue.

In this spirit of any repair, I replaced them, and it was not the issue. I don't know what I expected.

Ceiling. YouTube. Pacing.

Then I figured it was this part - the motor coupling. I unplugged the machine and took out the drain tube. I leaned the machine back and propped it up with an empty detergent bottle, because those were abundant. Ratchet off a few bolts and the motor comes out. The coupling was indeed broken. The new one slips right in - I tapped it a few times with a mallet for good measure / vengeance. Ratcheted the bolts back on and tipped it back up.

Pros: Washer works now.
Cons: Everest-esque laundry pile to address.

But hey, it worked! I am no handyman and it wasn't too bad at all. Half hour tops.

Found leveling spring loose on bottom of washer, the sheet metal on bottom of cabinet ad rusted through. Drilled new hole in sheet metal and installed new leveling spring. Greased hole with blue marine grease so it will last another 40 years.

Put new one on work good, but now can't pump no more .the problem now is the spin cycal broke and I not going to fix it. Thank for the part work good.

Disconnect power & water then drain hoses.
We flipped the washer on it's side to gain access to the bottom. There was no need to take off the back panel. Keep a 5 gallon bucket and a few rags handy for the extra water in the pump line.
Disconnected the wiring harness. Removed the brackets holding the motor. It's a little tight on the back bracket. It has a 1/4" hex nut on the back side, so I used a 1/4" drive socket (see: small). Removed the bolts holding the gear case (this makes it a lot easier). Disconnected the pump hose and rotated the motor & gear box and pulled forward. This gives you access to the coupling. Remove the broken part. Clean the area for debris. NOTE: each part of the coupling has 3 fingers (these are what breaks off), so check to make sure you get all broken parts. Insert the new coupling. It has 3 parts; the plastic fittings go on tight and need to be snug to the shaft. Use a screwdriver handle on the center and tap down with a small hammer. Spray silicone on the rubber coupler to allow a little better slide.
Reverse the process. Line the gear box and motor up and push back into the tub assembly. We used 2 people to do this. It's easier to have someone stand over it and hold / rotate the gear box while the other one can align the motor & bolt everything back on.
It took us an hour, however, if you were doing a couple you could get it down to 30 min. flat.
Go wash your clothes!