11074411600 Kenmore Washer - Instructions

First - I saw the picture of the part on your site. It made all the difference.
Then, I turned off the water supply, unplugged the washer, removed the screws holding the backing plate on the washing machine to expose the valve.
After that, it was as easy as removing two mounting screws, disconnecting the solenoids (just two connections), pulling out the old valve and replacing it with the new.
Pretty simple and a lot less pricey when you can wait a few days for a part to come in the mail.

I watched the video on changing the valve. Then ordered the part. The video showed exactly how to do the repair and it was so easy.

I followed the great step by step video instructions that you provided. The only difficulty was getting the plugs off the Water Inlet Valve. I had to use pliers (gently) to pull the two plugs off. I would highly recommend PartSelect to my friends.

Take top of washing machine off. Turn spikets off and remove hot and cold inlet hoses. Remove one screw holding part in place. Reach from front and take valve out. Unplug wiring harnesses. Reinstall the same way I took it off.

With the help of reading about other individuals and their problem, I was able to replace the water inlet valve in less than 30 minutes. Unscrewed two screws on top to reveal the flat springs. Popped the springs and released the back of the washer. Removed the old part and replaced with new. A lot easier than I thought.

I diagnosed by reversing the plugs on the hot/cold valves. I then removed the valve , cleaned it up and sprayed the electrical contacts with (Corrosion Block) and re-assembled. It still only had hot water. Ordered part, received part next day. When I went to install it I discovered that the (Corrosion Block) had penatrated and all was working! So now I have a spare valve.

Opened back panel and replaced valve - very easy

I just followed the instructions from a previous customer. Worked perfectly.

followed the video and was as simple as could be.

The installation of the Water Inlet Valve itself was a breeze. However, removing the back panel of the machine was what took so much time. It looks like a few screws and off it comes, right? NOT SO!! There are various clips and two brass hangers that are a real pain to get to. My advice is to contact Whirlpool and get instructions on removing the back panel before you start. PS: the machine works great! Thanks for the service.

The PartSelect DIY video made this repair so incredibly easy that even my not-super-handy husband and I were able to do it in about 15 minutes. (And I mostly watched because it doesn't require two people at all.) Every single step that was possibly needed was explained. We actually got the repair right on the first try -- no cussing, no bickering, nothing but a working washing machine in a quarter of an hour. In our book, DIY doesn't get any easier than this. We'll definitely be back for any parts our other old appliances need, and we won't be afraid to try future repairs ourselves. Saved a bundle!

On this particular washer you have to remove the top part of the machine. Where your controls are at, ie: water temp, water level, etc. It takes removing a few screws. Than you have to remove the back of the machine. Unhook the washer hoses going into your machine. This is where your part is on the inside of the back. Remove the back by a few sliding hooks. Unhook the electrial plugins going into the mixer (value inlet). There will be other plugins you have to unplug up around the water level, water temp areas (on top of the machine). Remove the old water inlet value, replace it with the new. Replace all plugin electrical parts and put the back back on. Put top back on, screw in the screws and try your new machine. NOTE: When it comes to these electrical plugins its not that hard. They are are different, they can only go in one way. My wires were all tied together so each plug was at that particular plugin length. Ex: The last plugin was the longest. Pretty easy to know where it go. The other ones were shorter. In other words it was pretty easy to know where they went after unplugging. So don't be scared to try this. There is one wire that is screwed into the metal for a ground wire. Just make sure you do get this back in for your safety. It's the only one that could be over looked. I am a female and I watched and helped my loving father take this machine apart. After this I put this part in myself. I was amazed that my machine was like new again. I agreed to tell my story because by others telling there story is what helped me. It saved me from buying a new machine. When I seen the stories on this particular problem I was ready to take the chance. I had already spent way more than that at the laundry mat. Thank you again and best wishes to you all.

I removed the backing plate from the top, rear side of the machine & opened it up enough to open the side alittle to access the valve...Once I put the new valve in, I put the back panel back on & cleaned up!! Washer works great Again!!

After my son received a repair quote of $130, I decided to help him and do the repair myself. I have replaced inlet valves before and ordered the part ($30) from partselect.com. I received the part in less than 2 days via regular FedEx. I used the Partselect installation video (very accurate) to familiarize myself on accessing the defective part. The job took less than 30 minutes. Unfortunately, it also took me another 30 minutes to clean out all the dust bunnies residing under, in, and in back of the washer.

I looked at the PartSelect video first. It was a tremendous help. I removed the two screws on the right and left front corners of the console and tilted back the console. I disconnected a small electrical plug on the top panel and removed two large metal clips under the console fastening the back panel to the top of the machine. I then slid the one-piece front, side, and top panels away from the back to reveal the inside of the machine (tub, motor, etc.). I then removed the old water valve (combined hot and cold water) from the back panel and instaled the new one, using the mounting plate. I then replaced the cover and reversed the procedure above, finally reinstalling the two screws on the console. The new water valve works perfectly!