11047892700 Kenmore Washer - Instructions

This was an easy fix . PartSelect was quick and had all the info I needed to repair my washer. Plus shipping was super fast. Thanks

Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Washed three loads and it was ok but then it stopped draining again. I don't know what to do.

Took the outer ring off with the help of pliers just be careful. Push the bellow into the washer. We cleaned the area good at this time. Put the new bellow in being sure to keep the wrinkles out and securing it in place with the other clamp. Make sure to keep it lined up and wrinkle free to prevent leaks and possible tears later on. You will need the screwdriver to tighten the screws in the inner clamp.

My son pulled the washer out and found the parts that was leaking. He ordered the parts from your company. they arrived the next day and he re-pared the leaks and all is well.thank you

First I want to acknowledge Parts Select for their prompt delivery(received parts in less than two days)and their unbeatable prices(approximately 1/3 less than two local appliance repair/parts shops). Repair was straight forward a simple swap of the pump and I saved quite a few dollars.Thanks Parts Select.Any future appliance parts needs will be purchased here.

It was easy as soon as I previewed a video on how to repair bellow it was all about unscrewing some screws and removing some parts but was simple steps that anyone can do themselves only thing that gave me very little trouble was putting the spring coil around the bellow needed my husband to help me a little so it wouldn't come out place while stretching the spring to make sure everything was good and secure and ran a test washer to make sure it didn't leak afterward.the baffle was very easy to replace with very little pressure I was able to slide it till I heard a click sound and it was secure did laundry same day and every was wonders very happy I was able to save some money on labor :)

Very limited access to the bellow clamp. Found it easier to first remove washer front panels (8 screws total), providing ready access to R&R the bellow. 40 minutes tops.

Removed the 3 bolts attaching top of washer. Disconnected hoses from the inlet value and flow meter, also very careful to remove the wire connections. Removed Water inlet valve (this requires the star screw driver). Did find it best to connect the inlet valve and flow meter before reattaching the inlet valve, as that sits under the lip, it is just a bit of a tight fit to get the hose reconnected between the two. Then reconnected the flow meter hose to the dispensing box, reattached the hoses and ran a cycle no f20 issues, as a note, an f20 has to do with a restriction in the flow of water not with pressure so not sure if it was the inlet valve or flow meter clogging up or both.

I removed the top 3 screws on the rear, removed soap dispenser, removed screw in front corner at soap dispenser,pry off control panel with flat head screwdriver lay on top, removed spring around bellows at door opening, remove 4screws holding door assembly, disconnect 3 molded plugs serving door lock, you will need to hold door while you loosen bellows clamp.Reverse process note: soap dispenser tube can be removed to clean without any tools. It is some much easier when you remove the front door assembly.T-20 torx screwdriver, 9/32 socket Theirs a you tube video also.ghw

A real novice at dyi. Found what the error code meant in the manual and google searched it online. Found Youtube video on repair and was successful in getting the washer to work a few times before the error code returned. Decided to replace the inlet valve and on your site took the advice of a previous user and also changed the flowmeter. Could not have been a better experience. Easy to find the correct parts for my model and got great tips...plus your shipping was excellent. Thanks!

Disconnected power. Turned of the water supply. Removed/disconnected the water lines from the washer. Removed the top by removing three screws. Disconnected the wires/connectors from the valve assembly. Disconnected the water line from the valve assembly to the dispenser assembly. Removed the screw holding the valve assembly on. Installed the valve assembly and reversed the above procedure.

Replaced pump assembly

I replaced the pump thinking this was the most likely cause of the problem. The pump is easy to access and get to. The reviews were helpful. The hose clamps were difficult to get back in place especially the one from the washer drain to the pump (need wide-jaw pliers). Now that I have seen the system work, the pump was not bad and the water from the drain still smells bad. I just ordered the filter 8181683, which looks like the only other thing that would prevent the water from draining completely. The drain hose is not blocked.

Looked at how the old drain pump was installed, then removed it and installed the new one. It was a fairly simple fix. The only feedback were that the parts picture was a little confusing becuase the picture didnt really look like the actual part, so we were unsure if we were ordering the correct part.